[2022年05月] 最新のCIP Level 1 NACE-CIP1-001試験解答豪華セット問題集
NACEコンテンツをマスターしてNACE-CIP1-001試験合格保証つき問題集!
質問 54
The Inspector's Log Book is generally:
- A. Submitted to the client upon project completion
- B. Retained by the inspector upon project completion
- C. Shared with all parties upon project completion
- D. Shredded by the inspector upon project completion
正解: B
質問 55
Upon arrival of coating materials, the inspector should
- A. observe and document the amount of material and batch numbers.
- B. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- C. observe aryl document that the applicator WFT at regular intervals during application.
- D. observe and document time frame and environmental conditions between each coat.
正解: A
質問 56
ISO SA 3 is directly equivalent to:
- A. NACE No. 2/SSPC SP 10
- B. NACE No. 1/SSPC SP 5
- C. None of the above
- D. NACE No. 3/SSPC SP 6
正解: C
質問 57
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 225 Gauge Readings resulting in 75 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 45 Gauge readings resulting in 15 Spot Measurements
正解: B
質問 58
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Stainless steel pipe to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Structural steel to be coated for Atmospheric Service
正解: C
質問 59
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
正解: B
質問 60
If a Thermoset coating is heated it will:
- A. Soften when heated and retain its softness when cooled
- B. Harden and retain its hardness when cooled
- C. Soften when heated and return to its original hardness when cooled
- D. Harden and return to its original hardness when cooled
正解: B
質問 61
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Call the supervisor
- B. Never change his/her mind
- C. Go with the majority opinion
- D. Achieve consensus through negotiation
正解: A
質問 62
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Taking measurements too far from the edge of a surface
- C. Measuring ditty, tacky, or soft films
- D. Failing to determine the base metal reading (BMR)
正解: A,C,D
質問 63
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Read the manufactures' instructions
- C. Ensure the instrument is within calibration parameters
- D. Be trained on how to use the instrument
正解: A
質問 64
The main responsibilities of the inspector are to
- A. observe and report the quality of the work performed.
- B. demonstrate to the contractor how to apply the coating.
- C. direct and perform the work stated in the specification.
- D. observe and direct the work of the contractors.
正解: A
質問 65
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. checking.
- B. holiday.
- C. sagging.
- D. cracking.
正解: B
質問 66
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Placing the gauge along the longitudinal axis
- B. Dragging a gauge through wet coating
- C. Using a damaged gauge
正解: B,C
質問 67
An Inspector should change position when:
- A. The Owner can save some money by the change
- B. The Inspectors position is not the majority position
- C. The Inspector is convinced by verifiable facts
- D. Only when directed by the supervisor
正解: C
質問 68
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Ultra-Violet light may contaminant the surface
- B. Synthetic oil or grease may not be identified
- C. Chloride salt may produce a false positive
- D. Presence of weld spatter may produce a false positive
正解: B
質問 69
According to SSPC PA 2 a Spot Measurement is:
- A. The average of gauge readings taken in a 4cm (1.5 inch) circle
- B. A single gauge reading
- C. The overall average of all readings
- D. The average of all spot measurements in a given area
正解: A
質問 70
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- B. Bring the matter up at the pre-job conference
- C. Default to the owner's Inspection and Test Plan
- D. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
正解: B
質問 71
Polymerization is the process of:
- A. Monomers telegraphing
- B. Monomers joining together
- C. All organic coatings
- D. All thermoplastic coatings
正解: B
質問 72
......
あなたを合格させるNACE NACE-CIP1-001試験専門問題集はここにある:https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu