199-01無料問題集「Riverbed Certified Solutions Professional」

質問 1

What are the SSL trusts that must be configured for a Steelhead Mobile client to successfully optimize SSL traffic? (Select 2)

（A）Steelhead Mobile clients trusts client-side Steelhead

（B）Steelhead Mobile clients trust Steelhead Mobile Controller

（C）Server-side Steelhead trusts Steelhead Mobile clients

（D）Client-side Steelhead, server-side Steelhead, Steelhead Mobile clients, and CMC appliance all must trust each other

正解：B、C 解答を投票する

質問 2

Which of the following authentication methods are supported by the Steelhead appliance?

（A）TACACS, RADIUS, Kerberos, and Local

（B）TACACS, RADIUS, and Local

（C）TACACS and Local

（D）TACACS, Kerberos, and Local

（E）RADIUS and Local

正解：B 解答を投票する

質問 3

What is contained in the probe of the return SYN/ACK packet when using enhanced auto-discovery (EAD)?

（A）4 bytes of notification

（B）14 bytes of TCP inner channel setup + 4 bytes of notification

（C）18 bytes of TCP inner channel setup + 4 bytes of notification

（D）32 bytes of TCP inner channel setup + 2 bytes of notification

（E）10 bytes of TCP inner channel setup + 2 bytes of notification

正解：B 解答を投票する

質問 4

Which of the following commands followed by "write memory" will allow you to turn off in-path optimization but turn it back on upon rebooting the Steelhead appliance?

（A）no in-path enable

（B）restart clean

（C）reload

（D）no service enable

（E）no interface in-path0_0 enable

正解：D 解答を投票する

質問 5

Which of the following custom TACACS+ attribute-value (AV) pairs gives the user guest privileges?

（A）local-user-name=guest

（B）local-user-name=ghost

（C）local-user-name=monitor

（D）local-user-name=administrator

（E）local-user-name=anonymous

正解：C 解答を投票する

質問 6

Select the command needed to add support for virtual in-path to your Steelhead appliance so that you can use WCCP or PBR with a Steelhead appliance.

（A）ip virtual enable

（B）in-path inpath0_0 enable

（C）in-path oop enable

（D）in-path virtual enable

（E）in-path wccp_pbr enable

正解：C 解答を投票する

質問 7

Refer to the exhibit.

Traffic going from Corp-A-DC-2 towards Corp-B will always use Link-1.Traffic from Corp-B back to Corp-A-DC-1 may traverse Corp-A-DC-1, over the GigaMAN before it reaches Corp-A-DC-2.No TCP connections are initiated from Corp-B to either Corp-A-DC-1 or Corp-A-DC-2.Unfortunately, the customer does not have any money to purchase any additional Steelheads.What are some possible fixes to ensure optimization occurs while Link-1 is operational? (If Link-1 ceases to function, optimization is not possible.)(Select 2)

（A）On the Corp-A-DC-2 Steelhead, enable "in-path probe direct"

（B）Enable Full Transparency

（C）Configure the Corp-A-DC-2 Steelhead to inject a route into the network

（D）On the Corp-B Steelhead, enable "in-path probe direct"

（E）Configure a fixed-target rule on the Corp-A-DC-2 Steelhead pointing to the Corp-B Steelhead on port 7800

正解：A、E 解答を投票する

質問 8

The IP address for which neighbor interface should be configured for Connection Forwarding? 1) lan0_0 2) inpath0_0 3) Primary 4) AUX 5) inpath7_7

（A）1, 2, 3, 4, 5

（B）1

（C）2, 3, 4, 5

（D）2

（E）1, 5

正解：D 解答を投票する

199-01 無料問題集「Riverbed Certified Solutions Professional」

弊社を連絡する

関連リンク

トップ試験