200-105 無料問題集「Cisco Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)」

（A）interface FastEthernet 0/0.30
encapsulation dot1Q 30
ip address 10.1.1.30 255.255.255.0

（B）interface FastEthernet 0/0
encapsulation dot1Q 30
ip address 10.1.1.30 255.255.255.0

（C）interface FastEthernet 0/0.30
ip address 10.1.1.30 255.255.255.0

（D）interface FastEthernet 0/0.30
description subinterface vlan 30

（A）Add the verify-data command to the IP SLA configuration.

（B）Use the debug ip sla error command on the device to troubleshoot.

（C）Add procative threshold conditions to the IP SLA to facilitate troubleshooting.

（D）Use the debug ip sla trace command on the device to troubleshoot.

（A）2001:0db8:0:130H::87C:140B

（B）2031:0:130F::9C0:876A:130B

（C）2001:0db8:0000:130F:0000:0000:08GC:140B

（D）2031::130F::9C0:876A:130B

（A）VSAT

（B）VPN

（C）MPLS

（D）DSL

（A）The backup port

（B）The designated port

（C）The root port

（D）The alternate port

（A）Network 172.16.1.33 mask 255.255.255.224

（B）Network 172.16.1.32 255.255.255.224

（C）Network 172.16.1.32 0.0.0.31

（D）Network 172.16.1.32 mask 255.255.255.224

（E）Network 172.16.1.32 mask 0.0.0.31

（F）Network 172.16.1.0 0.0.0.255

（A）Change the vlan ID to a value other than the default value

（B）Separate it from other vlans within administrative domain

（C）Assign it as a different vland id at each end of the link

（D）Assign it a value in the private vlan range

（E）Assign it as vlan1

（A）Router(config-if)# l2tp authentication

（B）Router(config)#aaa authentication ppp default local

（C）Router(config)# username router password password1

（D）Router(config-if)# ppp chap password password1

（A）debug chap authentication

（B）debug authentication

（C）debug chap ppp

（D）debug ppp authentication

（A）R1(config)#access-list 105 deny tcp 10.1.0.0 0.0.255.255 40.0.0.2 0.0.0.0 eq 53

（B）R1(config)#access-list 105 deny tcp 10.0.0.0 0.255.255.255 40.0.0.2 0.0.0.0 eq 53

（C）R1(config)#access-list 105 deny tcp 10.0.0.0 0.255.255.255 40.0.0.2 0.0.0.0 eq 443

（D）R1(config)#access-list 105 deny tcp 10.1.0.0 0.0.255.255 40.0.0.2 0.0.0.0 eq 443

（A）spanning-tree backbonefast

（B）spanning-tree mode rapid-pvst

（C）spanning-tree mode mst

（D）spanning-tree uplinkfast

（A）It requires the use of ARP.

（B）It supports up to 2 instances of OSPFv3 over a common link.

（C）It can support multiple IPv6 subnets on a single link.

（D）It routes over links rather than over networks.

（A）The router will return the packet to its source.

（B）The router will drop the packet.

（C）The router will forward the packet via either Serial0 or Serial1.

（D）The router will forward the packet via Serial2.

（A）B514 : 82C3 :: 0029 : EC7A : 0 : EC72

（B）B514 : 82C3 : 0029 :: EC7A : 0000 : EC72

（C）B514 : 82C3 : 0029 : EC7A : EC72

（D）B514 : 82C3 :: 0029 : EC7A : EC72