5V0-21.21無料問題集「VMware HCI Master Specialist」

質問 1

During a vSAN design workshop, a customer expressed a requirement to decommission an existing enterprise NAS device that provides iSCSI services for a clustered application.
Based on the current state analysis, the following information was noted:
* Current utilization is 500 LUNs.
* All clustered workloads are configured for Multiple Connections per Session.
* LUN sizes range between 10 TB to 30 TB.
What should the architect state regarding the requirements?

（A）The number of LUNs require additional licensing.

（B）It is a best practice to maintain a LUN size of 8 TB.

（C）All requirements can be satisfied without any change.

（D）Only single connection per session is supported.

正解：D 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 2

An administrator managing a vSAN cluster of six-nodes with policy FTT-2/RAID-6 decided to put one of the nodes in maintenance mode using the "Full-data migration" option.
What will happen after this action is taken?

（A）The system will prompt to add an additional host to the cluster in order to preserve the policy compliance.

（B）The host will enter into maintenance mode if both components of a certain object are residing on that host, then one of the components will be moved to another available host.

（C）The host will enter in maintenance mode and only data with no redundancy will remain accessible.

（D）The host will enter in maintenance mode and the data will remain accessible until the host exits maintenance mode.

正解：A 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 3

An administrator is planning to deploy workloads on a six node vSAN cluster, and all nodes are distributed equally across three racks.
Which action is required to ensure that the workload VMs remain compliant with the default vSAN policy after a complete rack failure?

（A）Add two additional hosts per rack, and configure vSAN with three fault domains and FTT=1.

（B）Add an additional host per rack, and configure vSAN with three fault domains and FTT=2.

（C）Add an additional rack with two hosts, and configure vSAN with four fault domains and FTT=1 (mirroring).

（D）Add an additional rack with two hosts, and configure vSAN with four fault domains and FTT=1 (erasure coding).

正解：C 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 4

An administrator has an absent capacity disk.
Which action, if any, should the administrator take to resolve the problem?

（A）Verify the host is not isolated.

（B）Replace the faulty host.

（C）Wait, and vSAN will rebuild it.

（D）Replace the faulty disk.

正解：D 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 5

Upon investigating a workload performance issue, a vSAN administrator observed a high backend IOPs on a vSAN cluster.
Which two causes explain this behavior? (Choose two.)

（A）The vSAN policy protection level has changed from FTT=0 to FTT=1.

（B）There is a vSAN node failure.

（C）The object repair timer value has been increased.

（D）The vSAN Resync throttling is enabled.

（E）The cluster DRS threshold has been set to Aggressive.

正解：A、B 解答を投票する

質問 6

Due to an update in their security requirements, an organization is no longer compliant because the metadata traffic between hosts in their vSAN cluster is not being encrypted.
Which step must be taken by the administrator to meet the new security requirements?

（A）Enable vMotion encryption on the vSAN cluster.

（B）Enable Data-In-Transit Encryption on the vSAN cluster.

（C）Enable virtual machine encryption on the vSAN cluster.

（D）Enable Data-At-Rest Encryption on the vSAN cluster.

正解：B 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 7

An architect is designing a vSAN cluster where the hosts have more than 512 GB of memory.
Which two boot devices are recommended for these hosts? (Choose two.)

正解：C、E 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

5V0-21.21 無料問題集「VMware HCI Master Specialist」

弊社を連絡する

関連リンク

トップ試験