642-035無料問題集「Cisco Troubleshooting Cisco Data Center Unified Computing」

質問 1

After migrating a server that is configured with dynamic vNICs, Cisco UCS Manager assigns new dynamic vNICs to the server. If you had been monitoring traffic on an original dynamic vNIC, what must you do when the server comes back up?"

（A）Reassign the dynamic vNIC back to the old configuration.

（B）Reassign the monitoring source.

（C）Remove and reconfigure the dynamic vNIC.

（D）Reassign the service profile back to the master one.

（E）Nothing; Cisco UCS Manager will take over.

正解：B 解答を投票する

質問 2

You are troubleshooting a remote Cisco UCS environment that has Cisco UCS 2208 I/O Modules. Some of the links from the IOMs to the UCS Fabric Interconnect fail to work as expected. You check whether the SFP is in place and the state of the IOM ports. Which command do you use to view the MAC and PHY status to determine whether the SFP is detected in the IOM?

（A）show platform software redwood oper

（B）show platform software woodsidests

（C）show platform software redwood post

（D）show platform software woodsideoper

正解：D 解答を投票する

質問 3

You attempt to boot a supported Linux operating system live image from the eUSB in a Cisco UCS blade-server environment, but the boot fails. Which option is the most likely cause of the failure?

（A）The blade servers are unable to boot from the eUSB. The eUSB is used only for virtual machines.

（B）Access to the eUSB is disabled for that blade server by Power Manager.

（C）In the Service Profile, a device other than the eUSB is set first in the boot order for the server.

（D）The eUSB license is unavailable or the grace period of the license is expired.

正解：C 解答を投票する

質問 4

Refer to the exhibit.

When this configuration is entered on a fabric interconnect, which traffic is added as a source for a monitoring session?

（A）the egress traffic on uplink port 3 on slot 1

（B）the ingress traffic on uplink port 3 on slot 1

（C）the ingress traffic on uplink port 1 on slot 3

（D）the egress traffic on uplink port 1 on slot 3

正解：A 解答を投票する

質問 5

On a Cisco UCS B-Series data center environment; how many default roles are there when utilizing RBAC for security restriction?

（A）20

（B）5

（C）1

（D）15

（E）10

正解：E 解答を投票する

質問 6

Which three methods can be used to upgrade the Cisco IMC? (Choose three.)

（A）host firmware package

（B）management firmware package

（C）directly on the blade, under the Blade Firmware tab

（D）controller firmware package

（E）directly on the blade, under the Installed Firmware tab

（F）directly on the blade, under Inventory > CIMC

（G）blade firmware package

正解：B、E、F 解答を投票する

質問 7

While updating firmware in a Cisco UCS environment, what will the Cisco UCS Manager do?

（A）show you only versions that are supported in your environment

（B）show you all versions available on Cisco.com

（C）show you only versions that you selected to show

（D）show you old and new versions from your download

（E）show you all versions downloaded to the Cisco UCS Manager

正解：A 解答を投票する

質問 8

Which CLI command identifies the service profile that is associated with a particular compute blade, VIF, vNIC type, link state, and pinned interface?

（A）show server-blade circuit server 1/2

（B）show service-profile circuit server 1/2

（C）show server-blade path server 1/2

（D）show service-profile path server 1/2

正解：B 解答を投票する

質問 9

Looking at the Equipment > Chassis > Servers > Server X view from the Cisco UCS Manager GUI, which tab would you select to identify the fabric interconnect uplink associated with a given virtual circuit?

（A）Virtual Circuit Paths

（B）VIF Paths

（C）vNIC Paths

（D）Paths

正解：B 解答を投票する

質問 10

HOTSPOT