642-980無料問題集「Cisco Troubleshooting Cisco Data Center Unified Fabric (DCUFT)」

質問 1

A customer is deploying FCoE in its network and has found that the connected host does not support FIP. Which command will be useful in troubleshooting this issue?

（A）show platform fcoe_mgr info software interface vfc id

（B）show platform software fcoe_mgr info interface vfc id

（C）show platform software interface fcoe_mgr info vfc id

（D）show platform fcoe_mgr info interface vfc id

正解：B 解答を投票する

質問 2

Refer to exhibit.

Customer has a pair of Cisco Nexus7010s switches and connected to a single Cisco
Nexus5548 switch via vPC. Customer has a combination of M1 and F1 I/O Modules in
Cisco Nexus7010s.
Why is the design described not supported?

（A）vPC does not support split control plane

（B）Mixing I/O Modules on the Same Side of a Peer Link is not supported

（C）Need to add another Cisco Nexus5548 switch to the topology to make this work.

（D）You can not configure a vPC peer link to configure two devices as vPCs

正解：B 解答を投票する

質問 3

To ensure that DCBX can be run on a switch, which other feature must be enabled?

（A）LLDP

（B）IEEE 802.1ad

（C）Cisco Discovery Protocol

（D）Fibre Channel

正解：A 解答を投票する

質問 4

You have enabled configuration synchronization between two Cisco Nexus 5548UP
Switches. You create a port channel on switch 1 and determine that it was not synchronized with its peer. The peer switch can be pinged on the management VRF. When you check your peer status, you receive a "peer not reachable" message in the command output. What is the explanation for this?

（A）UDLD is disabled.

（B）Multicast routing is enabled.

（C）CDP is disabled.

（D）An LACP mismatch exists on the peer interfaces.

（E）CFSoIP is disabled.

正解：E 解答を投票する

質問 5

Refer to the exhibit.

A zone merge failure occurs with the above error log. What is the problem?

（A）Two switches have different zone names and different members.

（B）Two switches have the same zone set name and the same members.

（C）Two switches have the same zone set name but different zone members.

（D）Two switches have different zone names.

正解：C 解答を投票する

質問 6

Which command shows failed validation commands when configurations are not merging between two switches while configuration synchronization feature on the Cisco Nexus 5548
Series Switches?

（A）# show configuration session <name>

（B）# show configuration session summary

（C）# show switch-profile peer

（D）# show switch-profile status

正解：D 解答を投票する

質問 7

NPV mode is not operating properly on a Cisco Nexus or Cisco MDS Series Switch. What are two reasons? (Choose two.)

（A）The VSAN does not match at each end of the connection.

（B）The license is invalid.

（C）An uplink NP port is stuck initializing.

（D）The VLAN does not match at each end of the connection.

正解：A、C 解答を投票する

質問 8

While troubleshooting HSRP adjacency, a packet analyzer captures the remote packet with the information: IP 224.0.0.102 with a MAC address of 0000.0C9F.0256. The DCI local group number is 256.
Which solution resolves the problem?

（A）Request that the remote data center verifies that they do not have an HSRP password configured.

（B）Report the issue as a suspected bug because the group number is correct based on the analyzer.

（C）Request that the remote data center change the HSRP version to V1.

（D）Request that the remote data center to use the correct HSRP group number.

（E）Change the local HSRP version to V1.

正解：D 解答を投票する

642-980 無料問題集「Cisco Troubleshooting Cisco Data Center Unified Fabric (DCUFT)」

弊社を連絡する

関連リンク

トップ試験