D-PEMX-DY-23無料問題集「EMC Dell PowerEdge MX Modular Deploy 2023」

質問 1

What is the benefit of C22 power inlet connectors on the MX7000 chassis?

（A）C22 connectors are now standard on PowerEdge

（B）Allow for higher exhaust temperatures

（C）Meet higher power requirements

（D）Enable linking together power supplies

正解：B 解答を投票する

質問 2

What are the typical ambient inlet temperature readings that ATMOS hardware and fans support?

（A）25°C (77°F), 30°C (86°F), and 35°C (95°F)

（B）30 uplink configuration combination of the Top of the Rack Switch and the MX70(104°F)

（C）20°C (68°F), 25°C (77°F), and 30°C (86°F)

（D）15°C (59°F), 20°C (68°F), and 25°C (77°F)

正解：B 解答を投票する

質問 3

Which protocol(s) does Redfish use?

（A）OData only

（B）JSON only

（C）JSON, OData, and SNMP

（D）JSON and OData only

正解：D 解答を投票する

質問 4

A server sled has a single mezzanine card installed in the correctly supported slot. To which IOM fabric(s) does the sled have access?

（A）Fabric A1 and Fabric A2

（B）Fabric A1 and Fabric B1

（C）Either Fabric A or Fabric B, depending on the configuration set in OME-M

（D）Fabric A1 only

正解：D 解答を投票する

質問 5

An administrator is configuring a fully populated MX5016s storage sled to be accessed by four MX740c compute sleds. Each compute sled has an H745P Jumbo PERC installed. The disks in the storage sled are evenly distributed across all compute sleds using a Drive-Assigned storage configuration.
What is the maximum number of disks that each compute sled can detect from the MX5016s?

（A）1

（B）16

（C）4

（D）2

正解：B 解答を投票する

質問 6

To which component can a firmware update be applied without affecting any applications running on the server?

（A）NIC

（B）BIOS

（C）RAID Controller

（D）iDRAC

正解：D 解答を投票する

質問 7

Which micro controller-based module allows the Management Module to communicate with all the hardware present in a PowerEdge MX7000 chassis?

（A）FReD

（B）iDRAC

（C）iSM

（D）EC

正解：A 解答を投票する

質問 8

Refer to the exhibit.

A customer recently replaced all the dual-port network cards in mezzanine A with quad-port network cards across all 16 PowerEdge MX740c sleds in the two-chassis configuration. The customer can only access half of the network ports, even though the quad-port cards are visible in the iDRAC.
What actions are required to resolve the problem?

（A）Do a virtual reseat of all the MX740c sleds.
Update the firmware on all the quad port network cards.
Adjust the switch configuration to use the new ports.

（B）Install a new 200G cable from port 3 on the MX7116n in chassis 2 slot A1 into port 19 on the MX9116n in chassis 1 slot A1.
Do the same for the switches in slots A2.
Adjust the switch configuration to use the new ports.

（C）Reboot the switches.
Adjust the switch configuration to use the new ports.

（D）Reseat all the switches.
Adjust the switch configuration to use the new ports.

正解：B 解答を投票する

質問 9

What is the port configuration of the MX9116n FSE?

（A）32 internal 25 GbE server facing ports
10 QSFP28-DD ports
4 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports

（B）16 internal 25 GbE server facing ports
12 QSFP28-DD ports
2 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports

（C）16 internal 25 GbE server facing ports
10 QSFP28-DD ports
4 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports

（D）32 internal 25 GbE server facing ports
12 QSFP28-DD ports
2 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports

正解：B 解答を投票する

質問 10

What compute sled model best supports the following requirements?
4 Node Database Cluster Heavy transactional workload 16 Processors
24 TB of DDR4 Memory
40 TB of Disk Space Maximum of 200,000 IOPS

（A）4 x MX840C 16 Processors
24 TB of DDR4 Memory
40 TB of Disk Space based on NVMe Drives

（B）4 x MX840C 16 Processors
24 TB of DDR4 Memory
40 TB of Disk Space based on SAS SSD Drives

（C）8 x MX740C 16 Processors
16 TB of DDR4 Memory
50 TB of Disk Space based on SAS SSD Drives

（D）8 x MX750C 16 Processors
16 TB of DDR4 Memory
45 TB of Disk Space based on NVMe Drives

正解：A 解答を投票する

D-PEMX-DY-23 無料問題集「EMC Dell PowerEdge MX Modular Deploy 2023」

弊社を連絡する

関連リンク

トップ試験