DNDNS-200無料問題集「EMC Dell Networking Professional」

質問 1

The network engineer powers on a new S-Series switch. None of the devices connected to this new switch are responding to pings.
Which two conditions should the network engineer verify? (Choose two.)

（A）ports are in switchport mode

（B）OSPF is enabled

（C）ports are not shut down

（D）the switch has a default Gateway

（E）an ARP table is configured

正解：C、E 解答を投票する

質問 2

Refer to the exhibit.
Considering the network topology and information shown, what is an issue with end point devices in network
192.168.102.0/24 that try to route to 192.168.101.0/24?

（A）Suboptimal Routing

（B）Routing Loop

（C）Summarization Black Hole

（D）ICMP Redirects

正解：B 解答を投票する

質問 3

The network engineer has two Dell Networking switches: an N-Series and an S-Series. Both switches have the factory default configuration. Which phrase correctly describes the current state of spanning-tree on both switches?

（A）S-Series Globally DisabledN-Series Globally Disabled

（B）S-Series Globally DisabledN-Series Globally Enabled

（C）S-Series Globally EnabledN-Series Globally Enabled

（D）S-Series Globally EnabledN-Series Globally Disabled

正解：B 解答を投票する

質問 4

A network engineer is implementing MLAG using two N-Series switches, MLAG must be set up with 10 Gb ports and connecting to a single S-Series switch that will run 802.3ad to the MLAG Peers. The commands will be identical on the two N-Series switches. All ports on the N-Series switches are available to use. The VLAN that must be used is 10. The management interface on each N-Series switch has already been assigned an IP address.
Which set of commands should be used to meet the requirement for MLAG?

（A）Option D

（B）Option B

（C）Option C

（D）Option A

正解：B 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 5

Refer to the exhibit.
The trunk links are being over utilized. A network engineer needs to resolve the issue by pruning the trunk links of unnecessary vlans. Each switch must be management accessible via VLAN 1.
What are the allowed vlans on each trunk link?

（A）Switch A [Te1/0/2 allowed VLAN 10]Switch B [Te1/0/2 allowed VLAN 10] [Te1/0/1 allowed VLAN
10, 20]Switch C [Te1/0/2 allowed VLAN 10] [Te1/0/1 allowed VLAN 10, 20]Switch D [Te1/0/2 allowed VLAN 10]

（B）Switch A [Te1/0/2 allowed VLAN 1, 10, 20]Switch B [Te1/0/2 allowed VLAN 1, 10, 20] [Te1/0/1 allowed VLAN 1, 10, 20]Switch C [Te1/0/2 allowed VLAN 1, 10, 20] [Te1/0/1 allowed VLAN 1, 10,
20]Switch D [Te1/0/2 allowed VLAN 1, 10, 20]

（C）Switch A [Te1/0/2 allowed VLAN 1-4096]Switch B [Te1/0/2 allowed VLAN 1-4096] [Te1/0/1 allowed VLAN 1-4096]Switch C [Te1/0/2 allowed VLAN 1-4096] [Te1/0/1 allowed VLAN 1-4096]Switch D
[Te1/0/2 allowed VLAN 1-4096]

（D）Switch A [Te1/0/2 allowed VLAN 1, 10]Switch B [Te1/0/2 allowed VLAN 1, 10] [Te1/0/1 allowed VLAN 1, 10, 20]Switch C [Te1/0/2 allowed VLAN 1, 10] [Te1/0/1 allowed VLAN 1, 10, 20]Switch D
[Te1/0/2 allowed VLAN 1, 10]

正解：B 解答を投票する

質問 6

A network deployment engineer needs to deploy four Dell Networking N1500 series switches. All switches are to be stacked together using 10Gbe ports on each switch and implement OSPF per the deployment plan.
The customer has been shipped only the four switches with SAS stacking cables. No other equipment has been shipped.
Which two issues occur when the network engineer tries to stack all four switches and implement OSPF?
(Choose two.)

（A）The N1500 series switches do not support advanced Layer 3 Functionality.

（B）Stacking modules were provided as per the deployment.

（C）Incorrect cabling was shipped for stacking instead of the required 10Gbs TwinAx.

（D）Stacking is limited to only four switches because of the limited back-plane bandwidth.

（E）The N1500 series switches support Layer 3 lite Functionality.

正解：C、E 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 7

Refer to the exhibit.
The deployment engineer needs to use rapid PVST+ so that some traffic is forwarding on all inter-switch links on these three N-Series Switches. To do so, each switch has been set to the lowest spanning-tree priority value for one of the VLANs.
Given the labeled diagram shown, what Spanning-Tree Priority is Switch B advertising for VLAN 20?

（A）4096

（B）4116

（C）32788

（D）0

正解：D 解答を投票する

質問 8

A network engineer needs to install five Dell N-Series switches in a stack for a company that is moving to a new building.
The following items are received:
- 5x Dell N4032 switches
- 5x Power cords
- 5x QSFP+ module card
- 120 CAT6 patch cords
- 1x UPS APC 7000
What needs to be provided to enable the network engineer to complete this task?

（A）TwinAx cables

（B）a USB drive with a configuration file

（C）Serial cables

（D）Memory RAM

正解：A 解答を投票する

質問 9

Refer to the exhibit.
Switch A needs to be able to have full reachability to the entire networking fabric through the use of static routes. All other devices have reachability to Switch A Which two static routers meet the requirement? (Choose two.)

（A）ip route 12.0.0.0 255.0.0.0 192.168.101.2

（B）ip route 12.0.0.0 255.0.0.0 192.168.101.1

（C）ip route 11.0.0.0 255.0.0.0 192.168.102.1

（D）ip route 11.0.0.0 255.0.0.0 192.168.102.2

正解：A、D 解答を投票する

DNDNS-200 無料問題集「EMC Dell Networking Professional」

弊社を連絡する

関連リンク

トップ試験