GB0-341-ENU 無料問題集「H3CSE-WLAN」

（A）H3C wireless controller series products exist in two forms: box type and plug-in card

（B）WX5002 series include WX5002-64, WX5002-128, which WX5002-64 default support 32AP, need to add a license to support 64 APs, while WX5002-128 default support 128 APs, without adding license.

（C）WX7300 series mainly include WX7306 and WX7310

（D）WX3000 series include WX3008, WX3010, WX3024, uu

（E）WX6000 series AC mainly includes WX6103, S7500/S7500E/S9500/S9500E plug-in cards

（A）False

（B）True

（A）24V/0.5 A

（B）24V/1.0 A

（C）48V/0.5 A

（D）48V/1.0 A

（A）CCK

（A）90

（B）45

（C）30

（D）60

（A）The network cable connecting the AP to the upstream PoE power supply device is recommended to be Category 5 or above

（B）The length of the network cable is recommended to be within 100 meters when the AP uses PoE power supply

（C）There is no requirement for the network cable connecting the AP to the upstream PoE power supply device.

（D）AP can support PoE module power supply or PoE switch power supply.

（A）False

（B）True

（A）Statically bind the wireless client MAC address and VLAN on the wireless controller

（B）After passing the authentication, Radius dynamically issues the client VLAN attributes

（C）Specify different VLAN attributes when adding the same service template (ie SSID) under different Aps

（A）Increased coverage in the vertical direction of the antenna

（B）Increased antenna coverage in the horizontal direction

（C）Reduced antenna coverage in the horizontal direction

（D）Reduced coverage in the vertical direction of the antenna

（A）When adding AP joint points on the original indoor sub-system, if the original system has power amplifier equipment, the AP joint position should be selected behind the power amplifier device.

（B）There are two ways to expand the capacity of the combined system. One is to modify the antenna at the end of the system, insert a combiner, and add APs; the other is to use a dedicated WLAN dual AP combiner

（C）Under normal circumstances, there cannot be more than 1 WLAN signal on the main path of the combined system, which will cause mutual interference of WLAN signals and fail to demodulate.

（D）For a distributed deployment design with the same environment layout on each floor, a uniform and symmetrical antenna feeder design can be selected. For example, the combined location of each floor, the number of APs, the number of couplers and power splitters, and the device specifications can all be unified

（A）wlan service-template 1 has been applied to the radio of the AP, you need to cancel the application first and then enter the command "wlanservice-template 1 crypto". If wlan service-template 1 is not applied, directly enter the command "wlan service-template 1" crypto".

（B）Enter the command "wlan service-template 1 crypto"

（C）You cannot modify the encryption type of the existing wlan service-template 1. You can only delete the original service-template 1, and then create a new service-template 1 through the command "wlan service-template crypto" to modify it to the purpose of the encryption type, but if wlan service-template1 has been applied to the radio of the AP, the relevant application needs to be released first.

（D）First try to enter "service-template disable" in service-template 1, then enter "wlan service-template 1 crypto" in the global view, and finally enter in the service-template 1 view.

（A）TAPA

（B）GRE

（C）LWAPP

（D）CAPWAP

（A）Ethereal

（B）Network Stumbler

（C）SecureCRT

（D）Microsoft Wireless Zero Configuration