HPE6-A66無料問題集「HP Aruba Certified Design Associate」

質問 1

Which two challenges do802.1ig barcode scanners present to a WLAN design? (Select two.)

（A）providing consistent performance on all available channels

（B）determining the RF channel bandwidth consumed per Barcode scanner

（C）roaming between APs

（D）encountering RF interference by devices

（E）implementing adequate security measures to ensure PCI compliance

正解：A、E 解答を投票する

質問 2

A network architect is doing a site survey for a new wireless design One concern the company has with the old wireless network is coverage. In some cases, APs would lose power and some employees in the network would lose wireless connectivity. The new design needs to prevent this issue from occurring. During the site survey, what are best practices to be followed in regards to the dBm signal level and the power of the AP to ensure adequate wireless coverage and minimal overlap of AP signals for the new design?

（A）AP power at 50% and a measurement of -65 dBM on the measuring device

（B）AP power at 75% and a measurement of -80 dBM on the measuring device

（C）AP power at 100% and a measurement of -65 dBM on the measuring device

（D）AP power at 75% and a measurement of -90 dBM on the measuring device

正解：C 解答を投票する

質問 3

A company is redesigning their wireless network and will be upgrading all devices to support the latest wireless standards. The company is not near any radar installations. In order to keep wireless NIC power levels as low as possible to reduce interference issues and to take advantage of radar frequency ranges, what IEEE standard should APs support?

（A）802.11 ax

（B）S02.11V

（C）802.11r

（D）S02.11h

正解：A 解答を投票する

質問 4

Which type of Aruba AP uses its radio as its back-haul connection?

（A）Remote AP (RAP)

（B）Air Monitor (AM)

（C）Mesh Porta

（D）Mesh Point

正解：C 解答を投票する

質問 5

A network architect is designing a new wired and wireless solution for for a company. The company has two buildings on a campus, which each building has three floors. The campus core will be placed in the basement of Building 1. Each wiring closet has eight strands of multi-mode OM3 grade fiber that connect to a wiring closet of the first floor of the building it is contained, referred to as a main distribution frame (MDF). The maximum distance between a floor's wiring closet and the MDF is 100 feet (30 meters). The maximum distance between the two MDFs and the campus core is no more than 150 feet (45 meters). There are eight strands of multi-mode OM3 grade fiber from these two MDF closets to the campus core.
Based on this information, which type of design should be used and what is the maximum speeds supported all uplinks for the existing the multi-mode fiber?

（A）three-tier and 10 Gbps

（B）three-tier and 40 Gbps

（C）two-tier and 10 Gbps

（D）two-tier and 40 Gbps

正解：A 解答を投票する

質問 6

A network architect will be using VisualRF to determine the appropriate wireless coverage for a new wireless design. Seamless, uninterrupted roaming is necessary for this design, since voice will need to be supported. Given these requirements, which information should be used in VisualRF to plan a cost effective solution that meets these requirements?

（A）Minimum -70db. 1 AP per 5,000 square feet, high density design

（B）Minimum -65db, 1 AP per 2,500 square feet, high density design

（C）Minimum -80db, 1 AP per 1,000 square feet, very high-density design

（D）Minimum -70db, 1 AP per 2,500 square feet, capacity design

正解：B 解答を投票する

HPE6-A66 無料問題集「HP Aruba Certified Design Associate」

弊社を連絡する

関連リンク

トップ試験