NACE-CIP1-001無料問題集「NACE Coating Inspector Level 1」

質問 1

The primary difference between Non-Convertible vs. Convertible coatings is:

（A）Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do

（B）Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not

（C）Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do

（D）Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not

正解：C 解答を投票する

質問 2

An Inspector should change position when:

（A）The Inspectors position is not the majority position

（B）The Inspector is convinced by verifiable facts

（C）Only when directed by the supervisor

（D）The Owner can save some money by the change

正解：B 解答を投票する

質問 3

You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:

（A）Skip the checks as you are. confident the blast pressure is OK

（B）Keep doing the checks regardless

（C）Skip the checks and just record the same readings as you have been getting

（D）Keep doing the checks and consult the Owner's representative for direction

正解：D 解答を投票する

質問 4

Surface profile describes:

（A）The level of surface roughness required after abrasive blasting

（B）The level of surface cleanliness required after abrasive blasting

（C）The initial condition of the surface prior to abrasive blasting

（D）The general condition of the surface required after abrasive blasting

正解：A 解答を投票する

質問 5

NACE Level 1 Inspectors have been trained to perform:

（A）Visual inspection, Non-Destructive and Destructive testing

（B）Visual inspection only

（C）All types of inspection

（D）Visual inspection and Non-destructive testing

正解：D 解答を投票する

質問 6

An inspectors personal log book should contain:

（A）Subjective comments re ding the application team

（B）No comments regarding the application team

（C）Objective comments regarding the application work

（D）The inspector's personal opinions of the application team

正解：B 解答を投票する

質問 7

What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?

（A）90% of the specified maximum thickness

（B）100% of the specified maximum thickness

（C）70% of the specified maximum thickness

（D）80% of the specified minimum thickness

正解：D 解答を投票する

質問 8

Which one of the following documents is the best source for coating technical data:

（A）Technical Data Sheet

（B）Safety Data Sheet;

（C）Specification

（D）Application Guidelines

正解：A 解答を投票する

質問 9

Passivation can best be described as:

（A）A coating layer applied to the surface to inhibit corrosion

（B）Treating metal with a liquid inhibiter

（C）A protective metallic oxide surface layer that slows corrosion

（D）Complete elimination pf the corrosion process

正解：C 解答を投票する

質問 10

The most important factor resulting in improved job site safety is:

（A）Situational Awareness

（B）Engineering Controls

（C）Personal Protective Equipment

（D）Safety Enforcement

正解：A 解答を投票する

NACE-CIP1-001 無料問題集「NACE Coating Inspector Level 1」

弊社を連絡する

関連リンク

トップ試験