NS0-194無料問題集「Network Appliance NetApp Certified Support Engineer」

質問 1

Referring to the exhibit, the UNIX user "prof1" will be looked up in which source first?

（A）files

（B）ldap

（C）dns

（D）nis

正解：C 解答を投票する

質問 2

After a network card was replaced in an ONTAP node, you see the output shown in the exhibit.

What is the problem?

（A）The interface group is configured in single mode.

（B）One physical port is not cabled.

（C）One physical interface is mis-cabled.

（D）One physical interface is broken.

正解：C 解答を投票する

質問 3

While troubleshooting intermittent takeover impossible command entries on the console, you request the output of the storage failover interconnect statistics error show command.
Which two counters would help troubleshoot this problem? (Choose two.)

（A）avg peer connection time

（B）sent queue length counter

（C）link error recovery counter

（D）peer connections lost

正解：B、C 解答を投票する

質問 4

You just set up a new clustered Data ONTAP 8.3 environment and want to monitor volume performance.
Which two commands or products would help you accomplish this task? (Choose two.)

（A）Quality of Service (QoS) commands

（B）Syslog Serve

（C）OnCommand Performance Manager

（D）OnCommand System Manager

正解：B、D 解答を投票する

質問 5

When you expend an aggregate, the space partition can be added as only a new RAID group, even though the current RAID group size is large enough for the current and new partitions.
In this scenario, which statement is correct?

（A）RAID group size is used only when dealing with non-partitioned disks.

（B）The partitions to be added share disks with the partition in the existing group.

（C）The aggregate must be converted to RAID-TEC to expand RAID groups using partitions.

（D）Only nonpartitioned disks can be added to RAID group with existing partitions.

正解：B 解答を投票する

質問 6

Exhibit:

You are provided output from the sysconfig -a and sysconfig -r commands of a MetroCluster cluster for disk switch 1:15.45 SN#J9YG1U3L, as shown In the exhibit.
Which two statements are true in this scenario? (Choose two.)

（A）The disk is located in switch3.

（B）The disk is located at the file3 site.

（C）The disk is located at the file2 site.

（D）The disk is in shelf 2 bay 13.

正解：B、D 解答を投票する

質問 7

You perform a security trace when troubleshooting a data access problem for a user. The results are shown in the exhibit.

What should you do to solve this issue?

（A）Add the user to the BUILTIN\Users group.

（B）Add the user to the BUILTIN\power Users group.

（C）Grant the user Read Attributes access to the path.

（D）Grant the user Execute access to the path.

正解：C 解答を投票する

質問 8

Exhibit:

You are attempting a storage giveback, but the process does not finish successfully. Referring to the exhibit.
What is the problem?

（A）An aggregate has failed.

（B）The giveback failed on the node root aggregate.

（C）There are active CIFS or NFSv4 connections.

（D）There are active cluster -02 was not ready for giveback.

正解：C 解答を投票する

質問 9

An administrator reviewing the message logs for a node notices an instance of a node reporting duplicate IPs for approximately ten seconds. Data access was not reported as interrupted during that time.
In this scenario, which process would generate these messages?

（A）mgwd

（B）vldb

（C）vifmgr

（D）bcomd

正解：C、D 解答を投票する

質問 10

You have a 4-node cluster configured for FC. You create a new LUN on node 1, map the LUN to a host, and verify that the host is able to correctly access the LUN. However, after moving the LUN's volume to node 3, ALUA reports that all the paths are non-optlmized. You have already verified that all zoning and physical cabling is correct.
What should you do to enable ALUA to see the optimized paths?

（A）Update the MPIO policy to round-robin.

（B）Update the MPIO policy to most recently used.

（C）Update the reporting nodes for the LUN mapping.

（D）Update the igroup initiator WWPN.

正解：C 解答を投票する

NS0-194 無料問題集「Network Appliance NetApp Certified Support Engineer」

弊社を連絡する

関連リンク

トップ試験