NSE5_FAZ-7.2無料問題集「Fortinet NSE 5 - FortiAnalyzer 7.2 Analyst」

質問 1

Refer to the exhibit.

What does the data point at 12:20 indicate?

（A）The log insert lag time is increasing.

（B）FortiAnalyzer is using its cache to avoid dropping logs.

（C）The performance of FortiAnalyzer is below the baseline.

（D）The sqlplugind service is caught up with new logs.

正解：D 解答を投票する

質問 2

Refer to the exhibits.

How many events will be added to the incident created after running this playbook?

（A）Five events will be added.

（B）Thirteen events will be added.

（C）Ten events will be added.

（D）No events will be added.

正解：B 解答を投票する

質問 3

Refer to the exhibit.

What is the purpose of using the Chart Builder feature on FortiAnalyzer?

（A）To add charts directly to generate reports in the current ADOM

（B）To build a chart automatically based on the top 100 log entries

（C）To add a new chart under FortiView to be used in new reports

（D）To build a dataset and chart automatically, based on the filtered search results

正解：A 解答を投票する

質問 4

What are analytics logs on FortiAnalyzer?

（A）Log type Traffic logs.

（B）Logs that roll over when the log file reaches a specific size.

（C）Raw logs that are compressed and saved to a log file.

（D）Logs that are indexed and stored in the SQL.

正解：D 解答を投票する

質問 5

Which statement about sending notifications with incident updates is true?

（A）Each connector used can have different notification settings.

（B）You must configure an output profile to send notifications by email.

（C）Notifications can be sent only when an incident is created or deleted.

（D）Each incident can send notifications to a single external platform.

正解：D 解答を投票する

質問 6

An administrator has configured the following settings:
config system fortiview settings
set resolve-ip enable
end
What is the significance of executing this command?

（A）It resolves the destination IP address to a hostname in FortiView on FortiAnalyzer.

（B）It resolves the source and destination IP addresses to a hostname in FortiView on FortiAnalyzer.

（C）You must configure local DNS servers on FortiGate for this command to resolve IP addresses on Forti Analyzer.

（D）Use this command only if the source IP addresses are not resolved on FortiGate.

正解：D 解答を投票する

質問 7

On the RAID management page, the disk status is listed asInitializing.
What does the statusInitializingindicate about what the FortiAnalyzer is currently doing?

（A）FortiAnalyzer is writing to all of its hard drives to make the array fault tolerant

（B）FortiAnalyzer is ensuring that the parity data of a redundant drive is valid

（C）FortiAnalyzer is functioning normally

（D）FortiAnalyzer is writing data to a newly added hard drive to restore it to an optimal state

正解：A 解答を投票する

質問 8

Which statement describes online logs on FortiAnalyzer?

（A）Logs that are saved to disk, compressed, and available in FortiView

（B）Logs that reached a specific size and were rolled over

（C）Logs that can be used to create reports

（D）Logs that can be viewed using Log Browse

正解：C 解答を投票する

質問 9

Which clause is considered mandatory in SELECT statements used by the FortiAnalyzer to generate reports?

（A）ORDER BY

（B）FROM

（C）LIMIT

（D）WHERE

正解：B 解答を投票する

質問 10

Logs are being deleted from one of the ADOMs earlier than the configured setting for archiving in the data policy.
What is the most likely problem?

（A）The ADOM disk quota is set too low, based on log rates

（B）The total disk space is insufficient and you need to add other disk

（C）Logs in that ADOM are being forwarded, in real-time, to another FortiAnalyzer device

（D）CPU resources are too high

正解：A 解答を投票する

NSE5_FAZ-7.2 無料問題集「Fortinet NSE 5 - FortiAnalyzer 7.2 Analyst」

弊社を連絡する

関連リンク

トップ試験