NSE6_SDW_AD-7.6無料問題集「Fortinet NSE 6 - SD-WAN 7.6 Enterprise Administrator」

質問 1

Within the context of SD-WAN, what does SIA correspond to?

（A）Local Breakout

（B）Software Internet Access

（C）Remote Breakout

（D）Secure Internet Authorization

正解：C 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 2

Which three factors about service-level agreement (SLA) targets and SD-WAN rules should you consider when configuring SD-WAN rules? (Choose three.)

（A）Best performance SD-WAN rules cannot use SLA targets.

（B）SLA targets are used by only SD-WAN rules that are configured with a lowest cost (SLA) strategy.

（C）When configuring an SD-WAN rule, you can select only one SLA target.

（D）Member metrics are measured when an SLA target references them.

（E）When configuring an SD-WAN rule, you can select multiple SLA targets from the same performance SLA.

正解：B、D、E 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 3

Refer to the exhibits.

You use FortiManager to configure SD-WAN on three branch devices.
When you install the device settings, FortiManager prompts you with the error "Copy Failed" for the device branch1_fgt. When you click the log button, FortiManager displays the message shown in the exhibit.
Based on the exhibits, which statement best describes the issue and how you can resolve it?

（A）Check the connection between branch1_fgt and FortiManager.

（B）Remove the installation target for the SD-WAN member port4. You cannot combine metadata variable and installation targets.

（C）Check the metadata variable definitions, and review the per-device mapping configuration.

（D）Gateways for all members in a zone must be defined the same way. Specify the gateway of the SD-WAN member port1 without metadata variables.

正解：C 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 4

Refer to the exhibit that shows VPN event logs on FortiGate.

Based on the output shown in the exhibit, which statement is true?

（A）There is one shortcut tunnel built from master tunnel T_MPLS_0.

（B）There are no IPsec tunnel statistics log messages for ADVPN shortcuts.

（C）The VPN tunnel T_MPLS_0 is a shortcut tunnel.

（D）The master tunnel T_INET_0 cannot accept the ADVPN shortcut.

正解：C 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 5

Refer to the exhibit, which shows an SD-WAN zone configuration on the FortiGate GUI. What can you conclude about the zone and member configuration on this device?

（A）You can move HUB1-VPN3 from the HUB1 zone to the overlay-shops zone.

（B）The underlay zone contains three members.

（C）The overlay-factories zone contains no member.

（D）You can delete the virtual-wan-link zones.

正解：A 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 6

You used the HUB IPsec_Recommended and the BRANCH IPsec_Recommended templates to define the overlay topology. Then, you used the SD-WAN template to define the SD- WAN members, rules, and performance SLAs.
You applied the changes to the devices and want to use the FortiManager monitors menu to get a graphical view that shows the status of each SD-WAN member.
Which statement best explains how to obtain this graphical view?

（A）Use the SD-WAN monitor template view to get a map view of the branches, hub, and tunnel status, including the SLA pass or missed status.

（B）Use the SD-WAN monitor table view to get a donut view and a table view that shows the status of each SD-WAN member, including the SLA pass or missed status.

（C）Use the VPN monitor map view to get a map view of the branches, hub, and tunnel status, including the SLA pass or missed status.

（D）Use the SD-WAN monitor asset view to get a donut view and a table view that shows the status of each device and the SLA status of each SD-WAN member.

正解：B 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 7

Refer to the exhibits.

You are using FortiManager to manage the branch devices and configure the SD-WAN template.
You update the configuration to address new user requirements and set the firewall policies shown in the second exhibit.
Then, when you use the install wizard to install the updated configuration and firewall policy package on the branch devices, FortiManager reports the error shown in the third exhibit.
Why can't FortiManager install the configuration on the branch devices?

（A）You cannot install firewall policies that reference an SD-WAN zone.

（B）You must direct traffic with the default security profile to a VPN tunnel.

（C）You cannot install firewall policies for HTTPS traffic with no SSL inspection.

（D）You cannot install firewall policies that reference an SD-WAN member.

正解：D 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 8

Refer to the exhibit, which shows the SD-WAN rule status and configuration.

Based on the exhibit, which change in the measured latency will first make HUB1-VPN3 the new preferred member?

（A）When HUB1-VPN3 has a lower latency than HUB1-VPN1 and HUB1-VPN2

（B）When HUB1-VPN3 has a latency of 80 ms

（C）When HUB1-VPN3 has a latency of 90 ms

（D）When HUB1-VPN1 has a latency of 200 ms

正解：B 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

NSE6_SDW_AD-7.6 無料問題集「Fortinet NSE 6 - SD-WAN 7.6 Enterprise Administrator」

弊社を連絡する

関連リンク

トップ試験