お手軽D-RP-OE-A-24問題集PDFのベスト問題集を使おう！高得点目指すならここ
Data Protection D-RP-OE-A-24試験と認定テストエンジン
EMC D-RP-OE-A-24 認定試験の出題範囲：
| トピック | 出題範囲 |
|---|---|
| トピック 1 |
|
| トピック 2 |
|
| トピック 3 |
|
| トピック 4 |
|
| トピック 5 |
|
質問 # 38
When replicating a Consistency Group between clusters using XtremlO at each site that are connected through Fibre Channel, what is the maximum throughput per RPA?
- A. 150 MB/s
- B. 300 MB/s
- C. 450 MB/s
- D. 240 MB/s
正解：B
解説：
When setting up replication for a Consistency Group between clusters using XtremIO storage arrays at each site connected through Fibre Channel, the maximum throughput that can be expected per RecoverPoint Appliance (RPA) is 300 MB/s. This throughput is a measure of how much data can be transferred from one site to another per second by each RPA involved in the replication process.
The throughput capacity is important for planning and ensuring that the RecoverPoint system can handle the expected data load during replication activities. It affects the Recovery Point Objective (RPO) and the overall efficiency of the disaster recovery setup.The 300 MB/s figure provides a benchmark for administrators to gauge the performance capabilities of their RecoverPoint system when used in conjunction with XtremIO storage arrays1.
It's important to note that actual throughput can vary based on several factors, including network conditions, the amount of data being replicated, and the specific configuration of the RecoverPoint and XtremIO systems1.
質問 # 39
A RecoverPoint administrator is using the CLI to create a new Consistency Group. After beginning the process by running the command create_group, what is the next command that needs to be run?
- A. create_replication_volume
- B. create_production_copy
- C. add_group_set
- D. add_replication_volume
正解：D
解説：
When using the CLI to create a new Consistency Group in RecoverPoint, after initiating the process with the create_group command, the next step involves adding volumes to the group. The add_replication_volume command is used to add a volume to a Consistency Group as a replication volume.This command specifies the volume to be replicated and associates it with the newly created group1.
The sequence of commands would typically follow this pattern:
* Run create_group to initiate the creation of a new Consistency Group.
* Run add_replication_volume to add each production volume that needs to be replicated within the Consistency Group.
* Additional commands would follow to configure the properties of the Consistency Group and its replication sets1.
It's important to note that the add_group_set command is used for different purposes, such as grouping multiple Consistency Groups together, and the create_replication_volume and create_production_copy commands are not standard commands in the RecoverPoint CLI for this context1.
質問 # 40
Which point-in-time image can be tied to application events and is created by a user command?
- A. Snapshot
- B. Bookmark
- C. Direct Access
- D. Virtual Image Access
正解：B
解説：
In Dell RecoverPoint, a Bookmark is a user-created point-in-time image that can be tied to specific application events. This feature allows users to mark a particular point in time within the continuous data protection timeline of RecoverPoint, which can be used for recovery purposes. Here's how it works:
* User Command: A user issues a command to create a Bookmark, typically through the RecoverPoint management interface or via scripting.
* Tied to Application Events: The Bookmark can be associated with specific application events, such as before and after a significant update or batch process.
* Point-in-Time Image: The Bookmark represents a point-in-time image of the data at the moment the
* Bookmark was created.
* Recovery: In the event of data corruption or loss, the Bookmark can be used to recover data to the exact state it was in at the time of the Bookmark.
Bookmarks are an integral part of RecoverPoint's data protection capabilities, providing flexibility and precision for data recovery operations1.
質問 # 41
A storage administrator has created a new Consistency Group with a remote copy. After enabling the new group, the administrator notices several other Consistency Groups are experiencing high load alerts.
What is possible cause for the high load conditions?
- A. Not enough licensed replication storage is available for the new Consistency Group
- B. Initialization is consuming all the WAN bandwidth
- C. Journal pool for the new Consistency Group is undersized
- D. Journal pool for the new Consistency Group has poor performing storage
正解：B
質問 # 42
When using a Distributed Consistency Group, additional traffic is generated between the primary RPA and secondary RPAs. Where is this increase in traffic observed?
- A. No additional traffic will be observed because host writes are multicast to all appliances in a cluster
- B. Additional traffic is seen on the management network between the RPAs
- C. Additional traffic is seen on the FC links between the RPAs
- D. Additional traffic is seen on the WAN network between the RPAs
正解：D
解説：
In a Distributed Consistency Group (DCG) configuration, the primary RPA and secondary RPAs work together to manage a larger data throughput than a single RPA can handle. This is achieved by dividing the workload among multiple RPAs. As a result, there is an increase in traffic observed on the WAN network between the RPAs.This is because the data that is being replicated needs to be transferred over the WAN to ensure that all RPAs have the necessary information to maintain consistency and data protection1.
The process involves:
* The primary RPA receives write I/Os from the production environment.
* The primary RPA then distributes the data to the secondary RPAs over the WAN.
* The secondary RPAs process the data and replicate it to their respective Journal volumes.
* This distribution of workload allows the DCG to handle higher throughput and IOPS rates than a single RPA could manage1.
It's important to note that while there is additional traffic on the WAN, this does not necessarily mean that the FC (Fibre Channel) links or management network are unaffected.However, the most significant increase in traffic is observed on the WAN network, which is the communication link between the RPAs in a DCG configuration1.
質問 # 43
A storage administrator has seen high-load events in their RecoverPoint environment. The administrator wants to review the performance data for the past week with RecoverPoint. In addition, the administrator wants the raw data saved to a spreadsheet to review and create graphs of system performance over a period of time.
Which CLI command should be used?
- A. balance_load
- B. detect_bottlenecks
- C. get_rpa_statistics
正解：A
解説：
To review the performance data for the past week in a RecoverPoint environment and save the raw data for further analysis, the export_statistics CLI command should be used. This command allows the administrator to export the performance statistics data, which can then be saved to a spreadsheet and used to create graphs or conduct detailed analysis of system performance over time. The steps to use this command are:
* Access the CLI: Log into the RecoverPoint CLI using the appropriate credentials.
* Execute the Command: Run the export_statistics command to gather the performance data.
* Save the Data: The command will generate the performance data, which can be saved to a file.
* Analyze the Data: Open the saved file in a spreadsheet application to review the data and create graphs as needed.
This command is particularly useful for administrators who need to monitor and analyze the performance of their RecoverPoint environment over a specific period1.
質問 # 44
Which tools are listed under "System Analysis and Tools" section of Unisphere for RecoverPoint?
- A. Detect Bottlenecks, Balance Load, Configure System Reports and Alerts
- B. Detect Bottlenecks, Balance Load, Collect System Information
- C. Users and Security, Configure System Reports and Alerts, Change Security Level
- D. Users and Security, Configure System Reports and Alerts, Collect System Information
正解：B
解説：
Under the "System Analysis and Tools" section of Unisphere for RecoverPoint, the tools listed are designed to assist administrators in analyzing and optimizing the RecoverPoint system. The tools include:
* Detect Bottlenecks: This tool helps identify any performance bottlenecks within the RecoverPoint system. It analyzes the flow of replication data and points out areas where there might be congestion or delays, allowing administrators to take corrective actions.
* Balance Load: The Balance Load tool is used to evenly distribute the workload across the RecoverPoint Appliances (RPAs) to prevent any single RPA from becoming a performance bottleneck. This ensures that the system operates efficiently and that replication tasks are completed in a timely manner.
* Collect System Information: This tool gathers comprehensive information about the RecoverPoint system's configuration and operation. It is useful for troubleshooting issues, performing system audits, and preparing for support calls or maintenance activities.
These tools are integral to maintaining the health and performance of the RecoverPoint environment and are accessible through the Unisphere for RecoverPoint interface1.
質問 # 45
A database team is performing tests against a PIT copy of data. Their write activity is going to exceed the currently allocated amount of space dedicated to Image Access mode.
What should be done to allow testing to continue without disruption to their testing?
- A. Use the config_copy_group= copy= policy image_access_log_size= CLI command
- B. Navigate to Protection > Manage Protection > Select the CG from the list and select the copy.
Click Edit Journal, and add one or more additional Journal volumes. - C. Expand the Journal volume using native array tools.
Navigate to Protection > Manage Protection > Select the CG from the list and select the copy.
Click Edit Journal, and then select "Expand Journal". - D. Navigate to Protection > Manage Protection > Select the CG from the list and select the copy.
Click Edit, and then increase the reserved image access percentage from 20%
正解：B
解説：
When the database team's write activity is expected to exceed the space allocated for Image Access mode in RecoverPoint, additional Journal volumes need to be added to accommodate the increased write activity. This can be done through the Unisphere for RecoverPoint interface:
* Navigate to Protection: Access the Protection menu in the Unisphere for RecoverPoint.
* Manage Protection: Go to the Manage Protection section.
* Select the Consistency Group (CG): Choose the appropriate CG from the list.
* Select the Copy: Click on the copy that is being used for the Point-in-Time (PIT) testing.
* Edit Journal: Click on the Edit Journal option.
* Add Journal Volumes: Add one or more additional Journal volumes to ensure there is enough space for the write activity during the testing periD.
By adding additional Journal volumes, the database team can continue their testing without disruption due to space limitations in the Image Access mode1.
質問 # 46
A RecoverPoint administrator wants to add volumes from an unlicensed array to a RecoverPoint/EX cluster.
Which supported RecoverPoint volume type(s) addresses the
administrator's requirement?
- A. Journal only
- B. Repository only
- C. Repository and Journal
正解：C
解説：
In a RecoverPoint/EX cluster, the administrator can add volumes from an unlicensed array as a repository volume.The repository volume is used for internal RecoverPoint operations, such as storing metadata and system information necessary for the RecoverPoint cluster to function1.
The repository volume does not require a license as it is not part of the data replication path and does not store user data. This allows the administrator to utilize storage from an unlicensed array for this purpose.However, for journal and copy volumes, which are directly involved in data protection and replication, a licensed array is required to ensure proper functionality and support1.
It is important to note that while the repository can be on an unlicensed array, all other volumes involved in replication (such as journal and copy volumes) must be on licensed arrays.This ensures compliance with licensing agreements and enables full support and functionality of the RecoverPoint system1.
For the most accurate and up-to-date information, it is always best to consult the latest official Dell RecoverPoint documentation or contact Dell EMC support directly1.
質問 # 47
When attempting to protect new XtremlO LUNs, the administrator is unable to add an XtremIO source LUN to the Consistency Group. What is a possible reason for this issue?
- A. RecoverPoint/EX only allows the protection of VNX arrays
- B. XtremIO LUN was created with a 512-byte block size
- C. XtremlO arrays are only protected with RecoverPoint for VMs
- D. XtremlO array was not licensed in RecoverPoint
正解：D
解説：
One possible reason for the inability to add an XtremIO source LUN to the Consistency Group in RecoverPoint could be that the XtremIO array was not licensed in RecoverPoint. Licensing is a critical step in enabling the features and functionalities of RecoverPoint for specific storagearrays.If the XtremIO array is not licensed, RecoverPoint would not recognize or allow the addition of its LUNs to a Consistency Group1.
Additionally, it's important to ensure that the RecoverPoint version supports the XtremIO array model.For instance, RecoverPoint does not support XtremIO X2 arrays until version 5.11. Therefore, if the RecoverPoint version is earlier than 5.1, it would not be able to replicate volumes from an XtremIO X2 array, which could manifest as an issue when trying to add LUNs to a Consistency Group.
For the most accurate and up-to-date information, it is always best to consult the latest official Dell RecoverPoint documentation or contact Dell EMC support directly.
質問 # 48
A RecoverPoint administrator is planning to use RecoverPoint to protect their applications. The administrator needs to protect 8192 production volumes. The RecoverPoint system has two physical RPA clusters using VNX arrays.
What is a possible Consistency Group configuration?
- A. 4096 replication sets, each with 1 remote copy and 1 local copy
- B. 4096 Consistency Groups, each with 1 remote copy and 1 local copy
- C. 8192 replication sets, each with 1 remote copy and 1 local copy
- D. 8192 Consistency Groups, each with 1 remote copy and 1 local copy
正解：A
質問 # 49
A company is using XtremlO for their RecoverPoint environment. They have approximately 100 GB of cumulative changes per day with the change being constant throughout the day. The company has a requirement to roll back 48 hours.
How should the Journals be sized and how should the copy policy be configured to ensure maximum protection with the least amount of storage used?
- A. 5 GB with the "Required Protection Window" set for 2 days
- B. 40 GB with the "Required Protection Window" set for 2 days
- C. 200 GB with the "Required Protection Window" set for Default
- D. 10 GB with the "Required Protection Window" set for 2 days
正解：C
解説：
* Calculate Daily Changes: With 100 GB of cumulative changes per day, the total amount of changes over two days would be 200 GB.
* Determine Journal Size: The Journal size must be large enough to store all the changes for the required rollback periD.Therefore, a Journal size of 200 GB is necessary.
* Set Protection Window: The "Required Protection Window" should be set for 2 days to match the rollback requirement.
* Configure Copy Policy: The copy policy should be configured to ensure that the Journal maintains the point-in-time images for at least 48 hours.
By following these steps, the company can ensure maximum protection with the least amount of storage used, while also meeting their rollback requirements1234.
質問 # 50
For which type of EMC storage array(s) is the RecoverPoint/BK used for in local backups?
- A. Data Domain
- B. Avamar
- C. NetWorker
- D. VNX/VNXe, Unity
正解：A
解説：
RecoverPoint/BK license mode is for local backup of Data Domain storage. RecoverPoint/BK is system-based licensing for all clusters in a RecoverPoint system:
*Synchronous replication
*Multipath I/O support
*Virtualization hypervisor support for Hyper-V and VMware platforms.
*Integration with VMware vCenter, VMware SRM and vSphere VAAI support
*Built-in bandwidth reduction
*Two to eight RecoverPoint appliances per RPA cluster for failure resiliency and throughput
* RecoverPoint/BK Overview:
* RecoverPoint/BK is a specialized licensing mode designed for local backup operations specifically aimed at EMC's Data Domain storage systems. It enhances the data protection capabilities by integrating with Data Domain for efficient backup and recovery processes.
* Functionality and Features:
* Local Backup: The RecoverPoint/BK license mode is particularly utilized for local backups of Data Domain storage arrays. It ensures that the data stored on Data Domain systems can be effectively backed up and restored locally.
* Synchronous Replication: Provides real-time data replication between the primary and backup locations to ensure data consistency.
* Multipath I/O Support: Ensures high availability and reliability by providing multiple data paths to storage.
* Hypervisor Support: Supports virtualization platforms such as Hyper-V and VMware, allowing integration with various virtualized environments.
* Integration with VMware: Supports integration with VMware vCenter, VMware SRM, and vSphere VAAI, enabling seamless management and operation within VMware environments.
* Bandwidth Reduction: Includes built-in features to reduce bandwidth usage during data replication and backup operations.
* Resiliency and Throughput: Supports two to eight RecoverPoint appliances per RPA cluster, enhancing failure resiliency and throughput for robust data protection.
* Reference from EMC Documentation:
* RecoverPoint/BK license mode is explicitly mentioned for local backups of Data Domain storage arrays, providing a comprehensive data protection solution with advanced features tailored for Data Domain.
質問 # 51
In Unisphere for RecoverPoint, which wizard will allow an administrator to manage and monitor all currently accessed copies undergoing testing, failover, and production recovery?
- A. Manage Recovery
- B. Manage Protection
- C. Test a Copy
- D. Protect Volumes
正解：A
解説：
In Unisphere for RecoverPoint, the "Manage Recovery" wizard is the tool that allows administrators to manage and monitor all currently accessed copies that are undergoing testing, failover, and production recovery. This wizard provides a centralized interface for overseeing the recovery operations and ensuring that they are proceeding as expected. It includes features to:
* View the status of recovery operations.
* Manage failover and failback processes.
* Monitor the progress of data synchronization and access during testing1.
This wizard is an essential part of the RecoverPoint management suite, providing administrators with the capabilities needed to ensure the continuity and integrity of their data protection processes1.
質問 # 52
A RecoverPoint storage administrator needs to protect a mission critical application. The application is stored on three volumes provisioned from a new VNX. Once the Consistency Group is created for the application, how many replication sets will the group contain?
- A. Determined by the number of copies
- B. 0
- C. 1
正解：B
解説：
In Dell RecoverPoint, a Consistency Group is built from one or more replication sets.Each replication set consists of a production volume plus any local or remote copy volumes to which it is replicating1. Since the mission-critical application is stored on three volumes, and each volume will be part of a replication set, the Consistency Group for the application will contain three replication sets.This ensures that all three volumes are protected and replicated as part of the RecoverPoint protection strategy1.
It's important to note that the number of replication sets in a Consistency Group is equal to the number of production volumes being replicated.Therefore, if an application spans multiple volumes, each volume will be part of its own replication set within the Consistency Group1.
質問 # 53
A storage administrator is selecting Test a Copy to enable an Image Access for an XtremIO-to-XtremIO Consistency Group. Why is Logged Access the only allowable access mode with this type of replication?
- A. XtremlO cannot process the changes to the Journal required for Virtual Access
- B. XtremlO uses snapshots which are instantly promoted as the SCSI personality of the copy
- C. Direct Access is not possible because the copy cannot be mounted on XtremIO
- D. XtremlO snapshots are not host accessible when using RecoverPoint
正解：B
解説：
* Snapshot Technology: XtremIO arrays use snapshot technology that allows for quick access to data at a specific point in time.
* Logged Access Mode: When using RecoverPoint with XtremIO arrays, Logged Access mode is used because it leverages the snapshot capabilities of XtremIO.
* Instant Promotion: The snapshots created by XtremIO are instantly promoted as the SCSI personality of the copy, making them immediately accessible to the host.
* Efficiency: This process is efficient because it does not require the Journal to roll forward or backward, which would be necessary for other access modes like Virtual Access.
This capability is part of what makes XtremIO an effective storage solution for environments requiring rapid access to multiple data points for testing, development, or recovery purposes12.
質問 # 54 
Based on the Consistency Group status shown in the exhibit, why is the local copy not connected to the production and remote copy?
- A. Connection to the local copy cluster has failed
- B. Local copy has failed
- C. Consistency Group is failing over
- D. Test a Copy wizard is in progress
正解：D
解説：
When the "Test a Copy" wizard is in progress in a Dell RecoverPoint environment, it temporarily disconnects the local copy from the production and remote copies to allow testing of the data at a specific point in time without affecting the ongoing replication and production operations. The steps involved are:
* Initiate Test a Copy: The administrator starts the "Test a Copy" wizard from the RecoverPoint management interface.
* Disconnect Local Copy: The wizard disconnects the local copy from the production and remote copies to isolate it for testing.
* Perform Testing: The administrator or users perform necessary tests on the local copy, which is now in an isolated state.
* Reconnect Local Copy: Once testing is complete, the wizard will reconnect the local copy to resume normal replication and protection operations.
This process ensures that testing can be conducted on a consistent dataset without impacting the production environment or replication processes1.
質問 # 55
Where are incoming writes sent to during the Write phase of the RecoverPoint workflow?
- A. Consistency Groups' assigned RPA
- B. Production Journal
- C. Remote clusters' primary RPA
- D. Copy Journal
正解：A
解説：
1.The production host writes data to the production volumes, but is first intercepted by the splitter. The splitter sends the write data to the RPA.
2.Immediately upon receipt of the write data, the local RPA returns an acknowledgement (ACK) to the splitter.
3.The splitter then writes the data to the production storage volume.
4.The storage system returns an ACK to the splitter upon successfully writing the data to storage.
5.The splitter sends an ACK to the host that the write has been completed successfully
質問 # 56
In order to balance the workload of a RecoverPoint system, an administrator decided to change the primary RPA for specific Consistency Groups. Where is this setting configured?
- A. Copy Policy tab for the production copy
- B. Copy Policy tab for the remote copy
- C. Group Policy tab for the Consistency Groups
- D. Link Policy tab for the Consistency Groups
正解：C
解説：
The setting to change the primary RecoverPoint Appliance (RPA) for specific Consistency Groups is configured under the Group Policy tab for the Consistency Groups.This tab allows administrators to manage and adjust policies that affect the entire Consistency Group, including the assignment of the primary RPA, which is responsible for managing the replication for the group1.
The process for changing the primary RPA typically involves:
* Accessing the Unisphere for RecoverPoint interface.
* Navigating to the Consistency Groups section.
* Selecting the specific Consistency Group to be modified.
* Going to the Group Policy tab.
* Adjusting the settings to designate a new primary RPA for the group.
This change can help balance the workload across the RPAs in the RecoverPoint system, ensuring that no single RPA becomes a performance bottleneck and that the replication process remains efficient and effective1.
質問 # 57
Why is Image Access instantaneous when testing a copy with XtremlO arrays?
- A. RecoverPoint performs initialization based on the DIFF result
- B. XtremlO completes the copy "roll back" as a background task
- C. No rolling forward or backward of the Journal is required
- D. RecoverPoint uses XtremIO synchronous Snap-based replication
正解：C
解説：
When using XtremIO arrays with RecoverPoint, Image Access is instantaneous because there is no need to roll the Journal forward or backward. This is due to the way XtremIO handles snapshots, which are used by RecoverPoint during the Image Access process:
* Snapshot Creation: XtremIO creates snapshots very efficiently, without the need for a full copy of the data. These snapshots are pointer-based, meaning they reference the original data without duplicating it.
* Instant Access: When Image Access is initiated, RecoverPoint can immediately present a snapshot to the host because it's simply a matter of accessing the pointers to the existing data, rather than having to roll data forward or backward in the Journal.
* Continuous Replication: Even while Image Access is in use, replication and distribution continue unaffected, ensuring that protection of the production data is maintained1.
This capability is part of what makes XtremIO an effective storage solution for environments requiring rapid access to multiple data points for testing, development, or recovery purposes1.
質問 # 58
If a RecoverPoint Consistency Group consists of three production volumes and each has two remote copies, how many replication sets will be contained in this group?
- A. 0
- B. 1
- C. 2
正解：A
質問 # 59
Which RecoverPoint feature allows for the creation of a consistent point-in-time image across multiple Consistency Groups?
- A. Snapshot Pruning
- B. Journal Consolidation
- C. Group Sets
- D. Bookmarks
正解：C
質問 # 60
What is the recommended wait period before running the Balance Load tool?
- A. 7 Days
- B. 6 Days
- C. 5 Days
正解：B
解説：
The Dell RecoverPoint documentation recommends a wait period of 7 days before running the Balance Load tool. This period allows for the system to stabilize and for any anomalies in the load distribution to become apparent, ensuring that the Balance Load tool can operate effectively. It's important to note that this information is based on the best practices outlined in the Dell RecoverPoint documentation and may be subject to change with different versions or specific system configurations.For the most accurate and up-to-date information, it is always best to consult the latest official Dell RecoverPoint documentation or contact Dell EMC support directly1.
質問 # 61
After a logical corruption, data on a production volume is inaccessible. As the volume is replicated using RecoverPoint, the administrator decides to use the "Test a Copy and Recover Production" wizard to restore this volume to its state prior to the logical corruption.
What is the correct sequence of steps to complete the recovery activity?
正解：
解説：
Explanation:
A screenshot of a recovery program Description automatically generated with medium confidence
To recover a production volume that has become inaccessible due to logical corruption using RecoverPoint's
"Test a Copy and Recover Production" wizard, follow these steps:
* Select a snapshot prior to the corruption: Identify and choose the appropriate point-in-time image from the Journal that was taken before the corruption occurred.
* Mount the snapshot to a verification host and verify its integrity: Attach the selected snapshot to a non-production host where you can perform checks to ensure the data is consistent and free from corruption.
* Unmount the production volume as the Recovery wizard will overwrite it with the recovery data:
Ensure that the current production volume is not in use because the recovery process will overwrite the existing data with the data from the snapshot.
* Monitor the progress of recovery from the Unisphere 'Manage Recovery' wizard: Use Dell EMC's Unisphere interface to track the recovery process and ensure that the data is being restored correctly.
These steps are based on the standard procedures outlined in Dell RecoverPoint documentation for using the "Test a Copy and Recover Production" wizard to restore volumes to a previous state1.
質問 # 62
Which Consistency Group setting is directly affected by the maximum Journal lag setting?
- A. Deduplication
- B. Compression
- C. RPO
正解：B
解説：
The Journal lag in a Dell RecoverPoint system refers to the amount of data that has been written to the production volumes but has not yet been replicated to the remote site or copy volumes. The maximum Journal lag setting affects the RPO because it determines the maximum allowable time or data volume that can pass before the data must be replicated to the remote site to meet the recovery objectives.
Here's how the Journal lag impacts the RPO:
* Journal Lag Definition: Journal lag is the measure of the difference between the most recent write to the production volume and what has been replicated to the copy volume.
* RPO Impact: The RPO is the maximum targeted period in which data might be lost from an IT service due to a major incident. If the Journal lag exceeds the maximum setting, itmeans that the RPO could be breached, as there would be more data at risk of being lost than what is acceptable per the RPO policy.
* Management Actions: Administrators can monitor and manage the Journal lag to ensure that the RPO is maintained. If the lag approaches the maximum setting, actions may be taken to increase replication throughput or address any issues causing replication delays.
In summary, the maximum Journal lag setting is crucial for ensuring that the RPO is met, as it directly influences the amount of data that could be lost in the event of a failure or disaster1.
質問 # 63
......
無料提供中のD-RP-OE-A-24試験問題集で（2025年最新のPDF問題集）信頼度の高いD-RP-OE-A-24テストエンジン：https://www.jpntest.com/shiken/D-RP-OE-A-24-mondaishu
D-RP-OE-A-24のPDFで最近更新された問題です集試験点数を伸ばそう：https://drive.google.com/open?id=1qLXPU5FoijcS737fYCGcbg3Q9Jhx_QUF