ベストJuniper JN0-683学習ガイドと問題集は2025年更新
トップクラスJuniper JN0-683試験最先端学習ガイド！練習問題バージョン
質問 # 35
You are asked to automatically provision new Juniper Networks devices in your network with minimal manual intervention Before you begin, which two statements are correct? (Choose two.)
- A. You must have a system log (syslog) server to manage system log messages and alerts.
- B. You must have a file server that stores software image and configuration files.
- C. You must have a DHCP server that provides the location of the software image and configuration files.
- D. You must have an NTP server to perform time synchronization.
正解：B、C
解説：
* Zero-Touch Provisioning (ZTP):
* ZTP is a feature that allows for the automatic provisioning of devices with minimal manual intervention. It is widely used in large-scale deployments to quickly bring new devices online.
* Key Requirements for ZTP:
* A. DHCP Server:A DHCP server is crucial for ZTP as it provides the necessary information to new devices, such as the IP address, the location of the software image, and configuration files.
* D. File Server:The file server is where the software image and configuration files are stored. The device downloads these files during the provisioning process.
* Incorrect Options:
* B. Syslog Server:While a syslog server is important for logging and monitoring, it is not a requirement for the initial provisioning process.
* C. NTP Server:An NTP server is used for time synchronization, which is essential for accurate logging and operation but not specifically required for ZTP.
Data Center References:
* ZTP simplifies the deployment process by automating the initial configuration steps, relying heavily on DHCP for communication and a file server for delivering the necessary configuration and software.
質問 # 36
Exhibit.
You have a sample configuration for connecting two sites through EVPN-VXLAN by exchanging IP prefix routes.
Referring to the exhibit, which two statements regarding the configuration are true? {Choose two.)
- A. The VNI should be unique on all devices for each customer site.
- B. The advertise direct-nexthop option enables the receiver to resolve the next-hop route using only information carried in the Type 5 route.
- C. The advertise direct-nexthop option enables the receiver to resolve the next-hop route using only information carried in the Type 2 route.
- D. The VNI must match on all devices for the same customer.
正解：B、D
解説：
EVPN-VXLAN Configuration:
* The configuration provided in the exhibit shows an EVPN-VXLAN setup where IP prefix routes are exchanged between two sites. The advertise direct-nexthop option and the VNI (Virtual Network Identifier) settings are crucial in this context.
Advertise Direct-Nexthop:
* Option A:The advertise direct-nexthop option ensures that the next-hop route is resolved using only the information carried in the EVPN Type 5 route. Type 5 routes are used for IP prefix advertisement in EVPN, which is key to enabling Layer 3 interconnectivity between different VXLAN segments.
VNI Consistency:
* Option C:For the same customer across different devices, the VNI must be consistent. This consistency ensures that all devices can correctly map traffic to the appropriate VXLAN segment, maintaining seamless Layer 2 and Layer 3 connectivity.
質問 # 37
You want to ensure thatVXLAN traffic from the xe-0/0/12 interlace is being encapsulatedby logical vlep.
32770 and sent to a remote leaf device in this scenario, which command would you use to verify that traffic is flowing?
- A. monitor traffic interface xe-0/0/12
- B. show interface terse vtep.32770
- C. show interfaces terse vtep.32770 statistics
- D. show interfaces vtep.32770 detail
正解：C
解説：
* VXLAN Traffic Verification:
* To ensure VXLAN traffic from the xe-0/0/12 interface is correctly encapsulated by the logical vtep.32770 and sent to a remote leaf device, it is essential to monitor the relevant interface statistics.
* The command show interfaces terse vtep.32770 statistics provides a concise overview of the traffic statistics for the specific VTEP interface, which can help verify whether traffic is being correctly encapsulated and transmitted.
* Explanation:
* This command is particularly useful for quickly checking the traffic counters and identifying any potential issues with VXLAN encapsulation or transmission.
* It allows you to confirm that traffic is flowing as expected, by checking the transmitted and received packet counters.
Data Center References:
* Monitoring interface statistics is a crucial step in troubleshooting and validating network traffic, particularly in complex overlay environments like EVPN-VXLAN.
質問 # 38
Exhibit.
You want to enable the border leaf device to send Type 5 routes of local networks to the border leaf device in another data center. What must be changed to the configuration shown in the exhibit to satisfy this requirement?
- A. Change: 5001 in the route-distinguisher to : 10010.
- B. Add encapsulation vxlan to the evpn hierarchy.
- C. Move vrf-target target: 65000:1 to the evpn hierarchy.
- D. Add a VLAN configuration with an 13-interface to the tenant1 routing instance.
正解：C
解説：
In this scenario, you want the border leaf device to advertise Type 5 EVPN routes to another border leaf in a different data center. Type 5 routes in EVPN are used to advertise IP prefixes, which means that for proper route advertisement, you need to configure the correct settings within the evpn hierarchy.
Step-by-Step Analysis:
* Understanding EVPN Type 5 Routes:
* EVPN Type 5 routes are used to advertise IP prefixes across EVPN instances, which allow different data centers or networks to exchange routing information effectively.
* VRF Target Setting:
* The vrf-target configuration is crucial because it defines the export and import policies for the VRF within the EVPN instance. For EVPN Type 5 routes to be advertised to other border leaf devices, the vrf-target needs to be correctly configured under the evpn hierarchy, not just within the routing instance.
Command to solve this:
move vrf-target target:65000:1 to evpn
* Other Options:
* Option B:Adding a VLAN configuration would not address the requirement to advertise Type 5 routes.
* Option C:Adding VXLAN encapsulation may be necessary for other scenarios but does not directly address the Type 5 route advertisement.
* Option D:Changing the route-distinguisher will differentiate routes but does not impact the advertisement of Type 5 routes to other data centers.
By moving the vrf-target to the evpn hierarchy, you enable the proper route advertisement, ensuring that the Type 5 routes for local networks are shared with other data center border leaf devices. This is aligned with best practices for multi-data center EVPN implementations, which emphasize the correct placement of routing policies within the EVPN configuration.
質問 # 39
You are designing an IP fabric tor a large data center, and you are concerned about growth and scalability.
Which two actions would you take to address these concerns? (Choose two.)
- A. Use OFX5700 Series devices as the super spines.
- B. Design a three-stage Clos IP fabric.
- C. Design a five-stage Clos IP fabric.
- D. Use EX4300 Series devices as the spine devices.
正解：A、B
解説：
* Clos IP Fabric Design:
* A Clos fabric is a network topology designed for scalable, high-performance data centers. It is typically arranged in multiple stages, providing redundancy, high bandwidth, and low latency.
* Three-Stage Clos Fabric:
* Option B:A three-stage Clos fabric, consisting of leaf, spine, and super spine layers, is widely used in data centers. This design scales well and allows for easy expansion by adding more leaf and spine devices as needed.
* Super Spines for Scalability:
* Option D:Using high-capacity devices like the QFX5700 Series as super spines can handle the increased traffic demands in large data centers and support future growth. These devices provide the necessary bandwidth and scalability for large-scale deployments.
Conclusion:
* Option B:Correct-A three-stage Clos fabric is a proven design that addresses growth and scalability concerns in large data centers.
* Option D:Correct-QFX5700 Series devices are suitable for use as super spines in large-scale environments due to their high performance.
質問 # 40
Why is a designated forwarder required in a multihomed CE-to-PE VXLAN environmentusing EVPN signalling?
- A. The designated forwarder is required to prevent flooding of MAC addresses to multihomed hosts.
- B. The designated forwarder is required to prevent duplicate packets from being received on multihomed hosts.
- C. The designated forwarder is required to prevent packets from looping between the PEs.
- D. The designated forwarder is required to prevent a traffic storm from being received on multihomed hosts.
正解：B
解説：
* Understanding Multihomed CE-to-PE VXLAN Environment:
* In a VXLAN environment using EVPN signaling, multiple PEs (Provider Edge devices) can be connected to the same CE (Customer Edge device). This setup is referred to as multihoming, where a CE device has multiple connections to the network to ensure redundancy and load balancing.
* Role of the Designated Forwarder:
* The designated forwarder (DF) is a mechanism used in EVPN to manage the forwarding of broadcast, unknown unicast, and multicast (BUM) traffic in a multihomed environment. The DF is selected to ensure that only one of the PEs forwards this type of traffic to the CE, preventing loops and unnecessary duplicate packets.
* Avoiding Duplicate Packets:
* Without a designated forwarder, all PEs connected to a multihomed CE could potentially forward the same packet to the CE, resulting in duplicate packets. This duplication can cause issues with packet processing on the CE, leading to inefficiencies and potential network problems.
Conclusion:
* Option D:Correct-The designated forwarder is essential to prevent duplicate packets from being received on multihomed hosts, ensuring that only one PE forwards BUM traffic to the CE.
質問 # 41
Whatare two supported methods (or exporting data when using the Junos telemetry interface? (Choose two.)
- A. using gRPC
- B. using SNMP
- C. using UDP
- D. using REST
正解：A、C
解説：
* Junos Telemetry Interface (JTI):
* The Junos Telemetry Interface is a framework that allows network operators to collect real-time telemetry data from Juniper devices. This data can be used for monitoring, analytics, and network automation.
* Data Export Methods:
* Option B:UDP (User Datagram Protocol)is a lightweight, connectionless protocol used for exporting telemetry data quickly with minimal overhead. While it doesn't guarantee delivery, it is suitable for high-speed data transfer where occasional packet loss is acceptable.
* Option D:gRPC (gRPC Remote Procedure Call)is a modern, high-performance method for data export that supports streaming and remote procedure calls, making it ideal for more complex telemetry data use cases.
Conclusion:
* Option B:Correct-UDP is supported for exporting telemetry data.
* Option D:Correct-gRPC is also supported, offering advanced streaming capabilities
質問 # 42
In your EVPN-VXAN environment, you want to prevent a multihomed server from receiving multiple copies ofBUM traffic in active/active scenarios. Which EVPN route type would satisfy this requirement?
- A. Type 5
- B. Type 7
- C. Type 8
- D. Type 4
正解：D
解説：
* Understanding the Scenario:
* In an EVPN-VXLAN environment, when using multi-homing in active/active scenarios, there's a risk that a multihomed server might receive duplicate copies of Broadcast, Unknown unicast, and Multicast (BUM) traffic. This is because multiple VTEPs might forward the same BUM traffic to the server.
* EVPN Route Types:
* Type 4 Route (Ethernet Segment Route):This route type is used to advertise the Ethernet Segment (ES) to which the device is connected. It is specifically used in multi-homing scenarios to signal the ES and its associated Ethernet Tag to all the remote VTEPs. The Type 4 route includes information that helps prevent BUM traffic duplication in active/active multi-homing by using a split-horizon mechanism, which ensures that traffic sent to a multihomed device does not get looped back.
* Explanation:
* The Type 4 route is crucial for ensuring that in a multi-homed setup, particularly in an active
/active configuration, BUM traffic does not result in duplication at the server. The route helps coordinate which VTEP is responsible for forwarding the BUM traffic to the server, thereby preventing duplicate traffic.
Data Center References:
* Type 4 routes are essential for managing multi-homing in EVPN to avoid the issues of BUM traffic duplication, which could otherwise lead to inefficiencies and potential network issues.
質問 # 43
Exhibit.
You are deploying a VXLAN overlay with EVPN as the control plane in an ERB architecture.
Referring to the exhibit, which three statements are correct about where the VXLAN gateways will be placed?
(Choose three.)
- A. Spine devices will have no VXLAN gateways.
- B. All leaf devices will have L3 VXLAN gateways.
- C. All leaf devices will have L2 VXLAN gateways.
- D. Only the spine devices will have L2 VXLAN gateways.
- E. Only the border and leaf devices will have L3 VXLAN gateways.
正解：A、B、C
解説：
* Understanding ERB Architecture:
* ERB (Edge Routed Bridging) architecture is a network design where the routing occurs at the edge (leaf devices) rather than in the spine devices. In a VXLAN overlay network with EVPN as the control plane, leaf devices typically act as both Layer 2 (L2) and Layer 3 (L3) VXLAN gateways.
* Placement of VXLAN Gateways:
* Option B:All leaf devices will have L2 VXLAN gateways to handle the bridging of VLAN traffic into VXLAN tunnels.
* Option C:All leaf devices will also have L3 VXLAN gateways to route traffic between different VXLAN segments (VNIs) and external networks.
* Option E:Spine devices in an ERB architecture generally do not function as VXLAN gateways.
They primarily focus on forwarding traffic between leaf nodes and do not handle VXLAN encapsulation/decapsulation.
Conclusion:
* Option B:Correct-All leaf devices will have L2 VXLAN gateways.
* Option C:Correct-All leaf devices will have L3 VXLAN gateways.
* Option E:Correct-Spine devices will not act as VXLAN gateways
質問 # 44
You are using a single tenant data center with a bridged overlay architecture. In this scenario, how do hosts of the different virtual networks communicate with each other?
- A. using anycast gateway addresses configured on the leaf devices
- B. using EVPN Type 5 routes
- C. using virtual gateway addresses configured on the spine
- D. off-fabric using an external device
正解：D
解説：
* Understanding Bridged Overlay Architecture:
* In a single-tenant data center using a bridged overlay architecture, virtual networks (VLANs) are typically isolated within the fabric, with traffic between these VLANs handled outside the fabric.
* Communication Between Different Virtual Networks:
* A. off-fabric using an external device:This is correct. In many bridged overlay architectures, communication between different virtual networks is handled off-fabric, often using an external router or firewall that connects the different VLANs. The fabric itself primarily provides Layer 2 connectivity within each VLAN, leaving inter-VLAN routing to be handled externally.
Data Center References:
* This design is common in smaller or simpler data center environments where a single tenant does not require complex on-fabric routing and prefers to handle inter-VLAN routing through dedicated devices.
質問 # 45
Whatare two ways in which an EVPN-signaled VXLAN is different from a multicast-signaled VXLAN?
(Choose two.)
- A. An EVPN-signaled VXLAN can perform autodiscovery of VTEPs using BGP.
- B. An EVPN-signaled VXLAN features slower and more complete convergence.
- C. An EVPN-signaled VXLAN is less resource intensive.
- D. An EVPN-signaled VXLAN can perform autodiscovery of VTEPs using IS-IS.
正解：A、C
解説：
* Multicast-Signaled VXLAN:
* In traditional multicast-signaled VXLAN, VTEPs (VXLAN Tunnel Endpoints) use multicast to flood and learn about remote VTEPs. This method relies on multicast in the underlay network to distribute BUM (Broadcast, Unknown unicast, and Multicast) traffic.
* This approach can be resource-intensive due to the need for multicast group management and increased network traffic, especially in large deployments.
* EVPN-Signaled VXLAN:
* EVPN-signaled VXLAN uses BGP (Border Gateway Protocol) to signal the presence of VTEPs and distribute MAC address information. BGP is used for VTEP autodiscovery and the distribution of endpoint information.
* This method is more efficient because it reduces the reliance on multicast, instead using BGP control-plane signaling to handle VTEP discovery and MAC learning, which reduces the overhead on the network and improves scalability.
* Correct Statements:
* B. An EVPN-signaled VXLAN can perform autodiscovery of VTEPs using BGP:This is correct because EVPN uses BGP for VTEP autodiscovery, making it more efficient and scalable compared to multicast-based methods.
* C. An EVPN-signaled VXLAN is less resource-intensive:This is correct because it eliminates the need for multicast flooding in the underlay, instead using BGP for signaling, which is less demanding on network resources.
* Incorrect Statements:
* A. An EVPN-signaled VXLAN can perform autodiscovery of VTEPs using IS-IS:This is incorrect because EVPN relies on BGP, not IS-IS, for VTEP discovery and signaling.
* D. An EVPN-signaled VXLAN features slower and more complete convergence:This is incorrect; EVPN with BGP typically provides faster convergence due to its use of a control plane rather than relying on data plane learning.
Data Center References:
* EVPN-VXLAN is widely adopted in modern data center designs due to its scalability, efficiency, and reduced resource consumption compared to multicast-based VXLAN solutions. It leverages the strengths of BGP for control-plane-driven operations, resulting in more efficient and scalable networks.
質問 # 46
You are preparing an sFlow monitoring system configuration.
In this scenario, what Information will be included in the datagram sent to the sFlow collector? (Choose two.)
- A. the sending device's serial number
- B. the interlace through which the packets entered the agent
- C. the source and destination VLAN for sampled packets
- D. the CRC from the sampled packet
正解：B、C
解説：
* Understanding sFlow Monitoring:
* sFlow is a packet sampling technology used to monitor traffic in a network. It sends sampled packet data and interface counters to an sFlow collector, which analyzes the traffic patterns.
* Information Included in sFlow Datagram:
* Option A:The datagram sent to the sFlow collector includes information about the interface through which the packets entered the agent (the switch or router). This is crucial for understanding where in the network the traffic was captured.
* Option D:sFlow datagrams also include the source and destination VLAN for the sampled packets. This allows for detailed analysis of the traffic flow within different VLANs.
Conclusion:
* Option A:Correct-The ingress interface is included in the sFlow datagram.
* Option D:Correct-The source and destination VLANs are also included, providing context for the sampled traffic.
質問 # 47
Exhibit.
Referring to the configuration shown in the exhibit, assume that there is no external router present, and that the configuration is fabric-only.
Which two statements are true about the example configuration? (Choose two.)
- A. Devices in irb.400 (vlan 400) are not able to communicate directly with devices in routing instance Customer A.
- B. VNI 10006is assigned to vlan 800 (irb.800).
- C. Devices in routing instance Customer A are able to communicate with devices in routing instance Customer B
- D. Devices in irb.400 (vlan 400) and irb.800 (vlan 800) are able to communicate over the fabric.
正解：A、D
解説：
* Understanding the Configuration:
* The exhibit shows configurations for two VRFs (Customer_A and Customer_B) with specific VLANs and VNIs assigned. Each VRF has interfaces (IRBs) associated with particular VLANs.
* Communication Between VLANs and Routing Instances:
* Option B:VLAN 400 (irb.400) is part of Customer_B, and there is no direct connection or routing between Customer_A and Customer_B in the configuration provided. Therefore, devices in irb.400 cannot communicate directly with devices in the Customer_A routing instance.
* Option D:Since irb.400 (VLAN 400) and irb.800 (VLAN 800) are part of the same routing instance (Customer_B), they can communicate over the fabric using VXLAN encapsulation.
Conclusion:
* Option B:Correct-There is no direct communication between devices in irb.400 (Customer_B) and routing instance Customer_A.
* Option D:Correct-Devices in VLAN 400 and VLAN 800 can communicate within the Customer_B routing instance over the fabric.
質問 # 48
Exhibit.
Given the configuration shown in the exhibit, why has the next hop remained the same for the EVPN routes advertised to the peer 203.0.113.2?
- A. EVPN routes cannot have the next hop changed.
- B. The export policy is incorrectly configured.
- C. The vrf-export parameter must be applied.
- D. The vpn-apply-export parameter must be applied to this peer.
正解：D
解説：
* Understanding the Configuration:
* The configuration shown in the exhibit involves an EVPN (Ethernet VPN) setup using BGP as the routing protocol. The export policy named CHANGE_NH is applied to the BGP group evpn- peer, which includes a rule to change the next hop for routes that match the policy.
* Issue with Next Hop Not Changing:
* The policy CHANGE_NH is correctly configured to change the next hop to 203.0.113.10 for the matching routes. However, the next hop remains unchanged when advertising EVPN routes to the peer 203.0.113.2.
* Reason for the Issue:
* In Junos OS, when exporting routes for VPNs (including EVPN), the next-hop change defined in a policy will not take effect unless the vpn-apply-export parameter is used inthe BGP configuration. This parameter ensures that the export policy is applied specifically to VPN routes.
* The vpn-apply-export parameter must be included to apply the next-hop change to EVPN routes.
* Correct Answer Explanation:
* D. The vpn-apply-export parameter must be applied to this peer:This is the correct solution because the next hop in EVPN routes won't be altered without this parameter in the BGP configuration. It instructs the BGP process to apply the export policy to the EVPN routes.
Data Center References:
* This behavior is standard in EVPN deployments with Juniper Networks devices, where the export policies applied to VPN routes require explicit invocation using vpn-apply-export to take effect.
質問 # 49
Exhibit.
Referring to the exhibit, the spinel device has an underlay BGP group that is configured to peer with its neighbors' directly connected interfaces. Which two statements are true in this scenario? (Choose two.)
- A. Load balancing for the underlay is configured correctly.
- B. The multihop statement is required to establish the underlay BGP sessions.
- C. Load balancing for the underlay is not configured correctly.
- D. The multihop statement is not required to establish the underlay BGP sessions.
正解：A、D
解説：
* Understanding BGP Configuration in the Exhibit:
* The exhibit shows a BGP configuration on spine1 with a group named underlay, configured to peer with directly connected interfaces of other devices in the network.
* Multipath multiple-as:This statement allows the router to install multiple paths in the routing table for routes learned from different ASes, facilitating load balancing.
* Key Statements:
* A. The multihop statement is not required to establish the underlay BGP sessions:In this case, the BGP peers are directly connected (as indicated by their neighbor IP addresses), so the multihop statement is unnecessary. Multihop is typically used when BGP peers are not directly connected and packets need to traverse multiple hops.
* D. Load balancing for the underlay is configured correctly:The multipath { multiple-as; } statement in the configuration enables load balancing across multiple paths from different autonomous systems, which is appropriate for underlay networks in data center fabrics.
* Incorrect Statements:
* C. The multihop statement is required to establish the underlay BGP sessions:This is incorrect because the peers are directly connected, making the multihop statement unnecessary.
* B. Load balancing for the underlay is not configured correctly:This is incorrect because the configuration includes the necessary multipath settings for load balancing.
Data Center References:
* BGP configurations in EVPN-VXLAN underlay networks are crucial for ensuring redundancy, load balancing, and efficient route propagation across the data center fabric.
質問 # 50
Exhibit.
The exhibit shows the truncated output of the show evpn database command.
Given this output, which two statements are correct about the host with MAC address 40:00:dc:01:00:04?
(Choose two.)
- A. The host is originating from an ESI LAG.
- B. The host is assigned IP address 10.4.4.5.
- C. The host is originating from irb.300.
- D. The host is located on VN110002.
正解：A、B
解説：
* Understanding the Output:
* The show evpn database command output shows the MAC address, VLAN, active source, timestamp, and IP address associated with various hosts in the EVPN instance.
* Analysis of the MAC Address:
* Option A:The MAC address 40:00:dc:01:00:04 is associated with the IP address 10.4.4.5, as indicated by the output in the IP address column. This confirms that this host has been assigned the IP 10.4.4.5.
* Option D:The active source for the MAC address 40:00:dc:01:00:04 is listed as 00:02:00:00:00:
04:00:04:00:00:04:00:04, which indicates that the host is connected via an ESI (Ethernet Segment Identifier) LAG (Link Aggregation Group). This setup is typicallyused in multi-homing scenarios to provide redundancy and load balancing across multiple physical links.
Conclusion:
* Option A:Correct-The host with MAC 40:00:dc:01:00:04 is assigned IP 10.4.4.5.
* Option D:Correct-The host is originating from an ESI LAG, as indicated by the active source value.
質問 # 51
Exhibit.
You have implemented an EVPN-VXLAN data center. Device served must be able to communicate with device server2.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. Traffic from server! to server2 will transit the VXLAN tunnel between leaf1 and Ieaf2.
- B. An IRB Interface must be configured on leaf1 and Ieaf2.
- C. Traffic from server1 to server2 will transit a VXLAN tunnel to spinel or spine2. then a VXLAN tunnel from spinel or spine2 to Ieaf2.
- D. An IRB interface must be configured on spinel and spine2.
正解：A、B
解説：
* Understanding the Exhibit Setup:
* The network diagram shows an EVPN-VXLAN setup, a common design for modern data centers enabling Layer 2 and Layer 3 services over an IP fabric.
* Leaf1 and Leaf2 are the leaf switches connected to Server1 and Server2, respectively, with each server in a different subnet (172.16.1.0/24 and 172.16.2.0/24).
* Spine1 and Spine2 are part of the IP fabric, interconnecting the leaf switches.
* EVPN-VXLAN Basics:
* EVPN (Ethernet VPN) provides Layer 2 and Layer 3 VPN services using MP-BGP.
* VXLAN (Virtual Extensible LAN) encapsulates Layer 2 frames into Layer 3 packets for transmission across an IP network.
* VTEP (VXLAN Tunnel Endpoint) interfaces on leaf devices handle VXLAN encapsulation and decapsulation.
* Integrated Routing and Bridging (IRB):
* IRB interfaces are required on leaf1 and leaf2 (where the endpoints are directly connected) to route between different subnets (in this case, between 172.16.1.0/24 and 172.16.2.0/24).
* The IRB interfaces provide the necessary L3 gateway functions for inter-subnet communication.
* Traffic Flow Analysis:
* Traffic from Server1 (172.16.1.1) destined for Server2 (172.16.2.1) must traverse from leaf1 to leaf2.
* The traffic will be VXLAN encapsulated on leaf1, sent over the IP fabric, and decapsulated on leaf2.
* Since the communication is between different subnets, the IRB interfaces on leaf1 and leaf2 are crucial for routing the traffic correctly.
* Correct Statements:
* C. An IRB Interface must be configured on leaf1 and leaf2:This is necessary to perform the inter-subnet routing for traffic between Server1 and Server2.
* D. Traffic from server1 to server2 will transit the VXLAN tunnel between leaf1 and leaf2:
This describes the correct VXLAN operation where the traffic is encapsulated by leaf1 and decapsulated by leaf2.
Data Center References:
* In EVPN-VXLAN architectures, the leaf switches often handle both Layer 2 switching and Layer 3 routing via IRB interfaces. This allows for efficient routing within the data center fabric without the need to involve the spine switches for every routing decision.
* The described traffic flow aligns with standard EVPN-VXLAN designs, where direct VXLAN tunnels between leaf switches enable seamless and scalable communication across a data center network.
質問 # 52
......
Juniper JN0-683 認定試験の出題範囲：
| トピック | 出題範囲 |
|---|---|
| トピック 1 |
|
| トピック 2 |
|
| トピック 3 |
|
| トピック 4 |
|
有効なJN0-683試験最新問題で2025年最新の学習ガイド：https://www.jpntest.com/shiken/JN0-683-mondaishu
JN0-683認定で究極のガイド：https://drive.google.com/open?id=1zcWuZMeQRZgr0P1eqbV6NiKZfesLNDfg