[2024年01月] 無料お試しCheckPoint 156-835問題集PDFは必ずベストの問題集オプションを使おう
156-835試験資料CheckPoint学習ガイド
156-835試験の受験資格は、有効なCheck Point Certified Security Expert（CCSE）またはCheck Point Certified Security Administrator（CCSA）認定を保持していることが必要です。試験は90問の多肢選択問題から成り、時間制限は120分です。試験の合格スコアは70％です。試験はMaestro Architecture、Maestro Deployment、Maestro Operations、Maestro Troubleshootingなどのトピックをカバーしています。試験に合格することで、2年間有効なCheck Point Certified Maestro Expert認定を取得することができます。
156-835試験に備えるために、候補者はネットワークセキュリティの概念を強く理解しており、Check Point Maestroに対する実践的な経験を持っている必要があります。Check Pointは、インストラクターによるコース、オンライントレーニングモジュール、自習教材など、候補者がスキルと知識を構築するのに役立つ様々なトレーニングと認定プログラムを提供しています。
チェックポイント認定のMaestro Expert認定は、IT業界で非常に評価されています。多くの組織による専門知識の検証として認識されており、雇用機会の増加と給与の増加につながる可能性があります。この認定は、多くのチェックポイントパートナープログラムの要件でもあり、認定専門家に追加の特典とリソースを提供します。
質問 # 32
What will happen in case of NAT of the traffic passing through Management network?
- A. Orchestrator will disable NAT and traffic will pass with no issue
- B. Since Management traffic is always going to SMO, it will take a care for Correction Layer and will re-distribute traffic to other Appliances
- C. This traffic will pass with no inspection
- D. This traffic will not pass correction, since it will be dropped
正解：D
質問 # 33
Splitter cannot be used __________.
- A. To connect single port on orchestrator to the same Appliance
- B. To connect single port on orchestrator to multiple Appliances
- C. To connect single port on orchestrator to multiple port on external switch
- D. To connect single port on Appliance to multiple ports on the orchestrator
正解：D
質問 # 34
When running asg perf -v in a Dual-Site environment, we can see only Appliances from one of the sites. That means we're working in:
- A. This is not Dual-Site, in Dual-Site we always see Appliances from both sites
- B. VSLS mode
- C. Active /Active
- D. Active / Standby HA mode
正解：D
質問 # 35
What command should be used for collecting diagnostic information about the orchestrator?
- A. cpview
- B. orch_info
- C. cpinfo
- D. asg pert -v
正解：B
質問 # 36
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?
- A. Port 1 in Slot 2 and Port 2 in Slot 1
- B. Any pair of available ports
- C. Port 1 in Slot 1 and Port 2 in Slot 1
- D. This configuration is not supported
正解：C
質問 # 37
What is the default IP range of Sync network (with no increment)?
- A. 192.168.1.0
- B. 198.51.100.0
- C. 192.0.2.0
- D. The same as Management network
正解：C
質問 # 38
In case of VSX: What is the right command to see overall performance details of all Appliances within the Security Group and all Virtual Systems?
- A. asg pert -v -p
- B. asg pert -v
- C. asg pert -vs enabled -p
- D. asg pert -vs all -v -vv
正解：D
質問 # 39
What is the default range of physical ports for downlinks on Orchestrator MHO-170?
- A. 25 - 32
- B. 3 - 16
- C. 1 - 16
- D. 17 - 31
正解：D
質問 # 40
What cannot be a reason for DETACHED status of Appliance when running asg monitor command?
- A. Appliance is a member of Security Group, but currently disconnected
- B. Appliance installed with R80.20
- C. There's an issue with Downlink cable
- D. Appliance reboots
正解：B
質問 # 41
How many power supplies are presented on MHO-140?
- A. 0
- B. 1
- C. 2
- D. 1 with option for 2
正解：C
質問 # 42
What is the throughput penalty of Security Group?
- A. 1% per member
- B. Depends on the type of Appliance
- C. 10% per Security Group with no relation to amount of members
- D. 5% per member
正解：B
質問 # 43
Which command will be used in order to restart Orchestrator service only?
- A. orchd restart
- B. service orchestrator restart
- C. reboot
- D. cpstop; cpstart
正解：A
解説：
Page 313 from the training manual:
- Restart the service:
orchd restart
- Restart the service without confirmation
service orchd restart
質問 # 44
What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?
- A. Three cables: uplink, downlink, SYNC
- B. Four cables: uplink, downlink, SYNC and Management
- C. Two cables: one uplink and one downlink
- D. One Downlink cable only
正解：D
質問 # 45
What is a Security Group?
- A. Group of appliances with enabled NGTX software blades
- B. Logical group of computer and network resources
- C. Group of security gateways
- D. Group of security administrators
正解：C
質問 # 46
What kind of cluster Dual-Site can be compared to?
- A. Active-Standby or VSLS
- B. Active-Standby only
- C. VSLS only
- D. Active-Active
正解：A
解説：
A Dual-Site cluster is a type of cluster that combines the features of both Active-Standby and VSLS (Virtual Systems Load Sharing) clusters. Dual-Site clusters allow you to have two active clusters, one at each site, and the traffic is distributed between the two sites based on predefined rules and priorities.
A Dual-Site cluster can be compared to an Active-Standby cluster because one of the clusters is running in a passive mode and is only activated in case of a failure or a planned maintenance of the active cluster. And also can be compared to a VSLS cluster because both clusters are active and share the traffic load.
It's a type of High Availability solution that provides redundancy and failover capabilities across two geographically separated sites. In case of a failure or a outage on one site, the traffic is automatically redirected to the other site, ensuring that the service is not interrupted.
質問 # 47
What is the minimal requirement for a Security Group?
- A. 1 Appliance and 1 administrator with Multi-Domain admin permissions
- B. None, it may be empty.
- C. 2 Appliances and 2 ports
- D. 1 Appliance and 1 management port
正解：D
質問 # 48
What is the maximum amount of Appliances within the same Security Group?
- A. 0
- B. 1
- C. 2
- D. 3
正解：A
質問 # 49
What does the lldpctl command do?
- A. Discover orchestrators
- B. Show all devices discovered by LLDP protocol on downlink ports
- C. Show all devices discovered by LLDP protocol on all ports
- D. Show all devices discovered by LLDP protocol on uplink ports
正解：C
質問 # 50
When running ifconfig command on an Appliance, there are interfaces shown in the list: ethl-Sync and eth2-Sync. What is the purpose of these interfaces?
- A. These interfaces are bond members (slaves) of Sync Bond
- B. These interfaces can be used as backup for Sync interface
- C. These interfaces represent physical Sync interface at the front panel of appliance
- D. These interfaces are not in use. Security GW module use Sync interface for synchronization
正解：C
質問 # 51
......
有効な問題最新版を試そう156-835テスト解釈156-835有効な試験ガイド：https://www.jpntest.com/shiken/156-835-mondaishu