GB0-191-ENU問題集を掴み取れ！[最新2024]H3C試験合格させます [Q51-Q68]

GB0-191-ENU問題集を掴み取れ！[最新2024]H3C試験合格させます

GB0-191-ENU試験問題集PDF正確率保証と更新された問題

質問 # 51
The WAN links of the customer's two routers MSR-1 and MSR-2 use the PPP protocol. At the same time, MSR-1 is required as the main verifier to verify MSR-2 through PAP. Then what configuration is required on MSR-2?

A. [MSR-2-Serial0/0] ppp pap local-user user password simple password
B. [MSR-2-Serial0/0] ppp pap password simple password
C. [MSR-2-Serial0/0] ppp pap user user
D. [MSR-2] ppp pap local-user user password simple password

正解：A

質問 # 52
Which of the following descriptions about Frame Relay DLCI are correct? (multiple choice)

A. DLCI is used to identify a physical interface or logical interface on the router
B. On the same link, each virtual circuit is identified by a unique DLCI
C. When the frame relay switching network transmits frame relay frames, it only changes its destination DLCI, that is, the value of the next hop DLCI, and does not change the value of the source DLCI of the sender
D. The range of DLCI that users can use is 16~1007

正解：B、D

質問 # 53
A network connection is like:
HostA----GE0/0--MSR-1--S1/0------S1/0--MSR-2--GE0/0----HostB
Among them, the two empty-configured MSR routers MSR-1 and MSR-2 are interconnected back-to-back through their S1/0 interfaces, and their GE0/0 interfaces are respectively connected to the client hosts HostA and HostB. All physical connections are normal.
Now add the following configuration under the S1/0 interface of MSR-2:
interface Serial1/0
link-protocol ppp
ppp pap local-user 123 password simple 456
ip address 6.6.6.1 255.255.255.0
So ______ . (Multiple choice)

A. Only need to configure PPP encapsulation and IP address 6.6.6.2/24 on the S1/0 interface of MSR-1 to communicate with each other
B. If only PPP encapsulation and IP address 6.6.6.2/24 are configured on the S1/0 interface of MSR-1, it cannot communicate
C. When performing PAP verification, MSR-2 will first send username 123 and password 456 to MSR-1
D. When performing PAP verification, MSR-2 will first send the password 456 to MSR-1 in clear text

正解：A、C

質問 # 54
On the MSR router, you can see the following display in the routing table:
Destination/Mask Proto Pre Cost NextHop Interface
127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0
127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0
192.168.96.0/19 Direct 0 0 192.168.120.153 S6/0
Then the correct description of the route with the destination address of 192.168.96.0/19 is ______.

A. This is a direct route with a metric value of 0
B. The interface IP address of S6/0 on this router is 192.168.120.153
C. The next hop of the router, that is, the IP address of the peer device is 192.168.120.153
D. This is a manually configured static route with a metric value of 0

正解：A、B

質問 # 55
Configure the unconfigured MSR router from the factory through the console port, and the baud rate of the terminal's serial port should be set to _____.

A. 0
B. 1
C. 2
D. 3

正解：A

質問 # 56
The command to start the spanning tree protocol on the switch is ____.

正解：

解説：
stp enable

質問 # 57
The following statement about the upgrade of H3C network equipment is correct ______. (Multiple choice)

A. When the device cannot boot to the command line mode and needs to upgrade the operating system software, only the Xmodem method can be used
B. In an environment where the complex interaction between the client and the server is not convenient, you can use TFTP to upgrade
C. Use Xmodem to upgrade to the same speed as FTP
D. When using FTP to upgrade, the device can only be used as an FTP client

正解：B

質問 # 58
The following description of the characteristics of VTY in H3C equipment is correct ______.

A. Each device can support simultaneous access by multiple VTY users
B. No password authentication is not supported
C. Each VTY user corresponds to a physical interface
D. Only used to Telnet the device

正解：A

質問 # 59
Two empty-configured MSR routers MSR-1 and MSR-2 are interconnected back-to-back through their respective S1/0 interfaces, and their respective GigabitEthernet0/0 interfaces
Connect the client hosts HostA and HostB respectively:
HostA----GE0/0--MSR-1--S1/0---------S1/0--MSR-2--GE0/0----HostB
Then make the following configuration on the two routers:
Configuration on MSR-1:
[MSR-1]interface GigabitEthernet 0/0
[MSR-1-GigabitEthernet0/0]ip add 192.168.1.1 24
[MSR-1]interface Serial 1/0
[MSR-1-Serial1/0]ip address 30.3.3.1 30
[MSR-1]rip
[MSR-1-rip-1]network 0.0.0.0
Configuration on MSR-2:
[MSR-2]interface GigabitEthernet 0/0
[MSR-2-GigabitEthernet0/0] ip address 10.10.10.1 24
[MSR-2]interface Serial 1/0
[MSR-2-Serial1/0]ip address 30.3.3.2 30
[MSR-2]rip
[MSR-2-rip-1]network 10.10.10.0
[MSR-2-rip-1]network 30.3.3.1
According to the above configuration, the WAN interface between the two routers can communicate with each other, other physical links in the network are good, and the two hosts HostA,
HostB can ping the address of their gateway GigabitEthernet0/0, so the following statement is correct _____.

A. The command network 30.3.3.1 on MSR-2 is configured incorrectly, it should be network 30.3.3.2
B. There is no RIP route in the routing table of MSR-2
C. The above three items are all wrong, the two routers can learn RIP routing
D. The command network 0.0.0.0 on MSR-1 is configured incorrectly, and the specific network segment should be configured

正解：C

質問 # 60
The default control protocol port used by FTP is ______.

A. 0
B. 1
C. 2
D. 3

正解：D

質問 # 61
The subnet mask of IP address 132.119.100.200 is 255.255.255.240, so the broadcast address of its subnet is ______.

A. 132.119.100.255
B. 132.119.100.193
C. 132.119.100.207
D. 132.119.100.223

正解：C

質問 # 62
If the broadcast flag in the DHCP Discovery message sent by the DHCP client to the DHCP relay is 0, the DHCP relay responds to the DHCP offer message of the DHCP client with ______.

A. broadcast
B. anycast
C. unicast
D. multicast

正解：C

質問 # 63
On the MSR router, the configuration file is a file saved in ______ format.

A. Batch file
B. text file
C. database file
D. executable file

正解：B

質問 # 64
Connect the two switches with an Ethernet cable, and the MDI type of the interconnection port is configured as across, then the Ethernet cable should be ________.

A. Only use a straight-through network cable
B. Parallel network cable and cross network cable are not acceptable
C. Both parallel and crossover cables are available
D. Only use crossover cable

正解：D

質問 # 65
The user router S0/0 is connected to the frame relay network, and the following information is displayed on the interface of the router: Serial1/1 current state:UP Line protocol current state:DOWN Internet Address is 3.3.3.2/24 The protocol state of the interface is DOWN, Then analyze ______ accordingly.

A. The encapsulated LMI type may be inconsistent with the remote end
B. The interface may encapsulate the PPP protocol
C. If the interface is encapsulated with the Frame Relay protocol, the status of the PVC should be DOWN at this time
D. The physical link may be faulty

正解：A、B

質問 # 66
The two empty-configured routers MSR-1 and MSR-2 are connected as follows: HostA----GE0/0--MSR-1--S1/0---------S1/0-- MSR-2--GE0/0----HostB
The WAN interconnection network segment of the two routers is 192.168.10.0/30, and the GE0/0 address of MSR-1 is 172.16.1.1/24.
After configuration, HostA can ping through 172.16.1.1, and the WAN between the two routers is also interoperable.
Now the following configuration is added to MSR-1:
[MSR-1]rip
[MSR-1-rip-1]network 192.168.10.1
[MSR-1-rip-1]network 172.16.1.1
And started the RIP process on MSR-2.
Which of the following configurations must be done on the MSR-2 to ensure that the MSR-2 learns the RIP route? (multiple choice)

A. [MSR-2-rip-1]network *.*.*.*, where *.*.*.* is any IP address on MSR-2
B. [MSR-2-rip-1]network 0.0.0.0
C. [MSR-2-rip-1]network *.*.*.*, where *.*.*.* is any IP address
D. [MSR-2-rip-1]network 192.168.10.1

正解：B、D

質問 # 67
The network environment is shown in the figure. Do the following NAT configuration on router RTA:

[RTA]acl number 2000
[RTA-acl-basic-2000]rule 0 permit source 100.0.0.0 0.0.0.255
[RTA]nat address-group 1 200.76.28.11 200.76.28.20
[RTA]interface Ethernet0/1
[RTA-Ethernet0/1]nat outbound 2000 address-group 1 no-pat
After configuration, Client_A and Client_B access Server at the same time, then the content of RTA's NAT table may be ______ at this time.

A. Protocol GlobalAddr Port InsideAddr Port DestAddr Port-200.76.28.11 --- 100.0.0.2 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00: 04:00-200.76.28.12 --- 100.0.0.1 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00:03:59 1 200.76.28.21 1024 100.0.0.1 1024 200.76.29.4 1024 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:00:59 1 200.76.28.11 512 100.0.0.2 512 200.76.29.4 512 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:01:00
B. Protocol GlobalAddr Port InsideAddr Port DestAddr Port-200.76.28.11 --- 100.0.0.2 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00: 04:00-200.76.28.12 --- 100.0.0.1 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00:03:59 1 200.76.28.12 1024 100.0.0.1 1024 200.76.29.4 1024 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:00:59 1 200.76.28.11 512 100.0.0.2 512 200.76.29.4 512 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:01:00
C. Protocol GlobalAddr Port InsideAddr Port DestAddr Port-200.76.28.11 --- 100.0.0.2 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00: 04:00-200.76.28.12 --- 100.0.0.1 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00:03:59 1 200.76.28.12 1024 100.0.0.1 1024 200.76.29.4 1024 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:00:59 1 200.76.28.11 511 100.0.0.2 512 200.76.29.4 512 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:01:00
D. Protocol GlobalAddr Port InsideAddr Port DestAddr Port-200.76.28.11 --- 100.0.0.2 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00: 04:00-200.76.28.12 --- 100.0.0.1 --- --- --- VPN: 0, status: NOPAT, TTL: 00:04:00, Left: 00:03:59 1 200.76.28.12 1023 100.0.0.1 1024 200.76.29.4 1024 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:00:59 1 200.76.28.11 511 100.0.0.2 511 200.76.29.4 512 VPN: 0, status: NOPAT, TTL: 00:01:00, Left: 00:01:00

正解：B

質問 # 68
......

最新をゲットせよ！GB0-191-ENU認定練習テスト問題試験問題集：https://www.jpntest.com/shiken/GB0-191-ENU-mondaishu