NS0-521問題集最新版を今すぐ試そう！[2024年11月] 試験準備には欠かせません！
有能な受験者がシミュレーション済みのNS0-521試験PDF問題を試そう
Network Appliance NS0-521 認定試験の出題範囲：
| トピック | 出題範囲 |
|---|---|
| トピック 1 |
|
| トピック 2 |
|
| トピック 3 |
|
| トピック 4 |
|
| トピック 5 |
|
| トピック 6 |
|
| トピック 7 |
|
| トピック 8 |
|
質問 # 37
A site survey has been conducted for an installation of a switchless HA pair with two NetApp DS224C shelves in the customer's already populated rack.
Which of the following two need to be verified to ensure a successful deployment? (Choose two.)
- A. Power connections
- B. Rack units
- C. Crash cart location
- D. Cluster switch location
正解：A、B
解説：
For a successful deployment of a switchless HA pair with two NetApp DS224C shelves in an already populated rack, it is crucial to verify:
* Rack units: Ensure that there are enough rack units available to accommodate the new shelves and any associated equipment. Proper planning of space in the rack is essential for a neat and functional setup.
* Power connections: Verify that there are sufficient and appropriately rated power connections available. Ensuring proper power distribution and redundancy is critical for the reliability and uptime of the storage system.
For more details, refer to:
* NetApp Documentation on Rack Installation
* NetApp Community Discussion on Power Connections
質問 # 38
What Is modified when moving a LUN between different HA pairs in the same SVM to prevent loss of connectivity?
- A. reporting nodes
Cigroup - B. LUN mapping
- C. port name
正解：A
解説：
When moving a LUN between different HA pairs in the same SVM to prevent loss of connectivity, the reporting nodes must be modified. The reporting nodes configuration ensures that the initiator paths are properly updated to reflect the new physical location of the LUN. This prevents disruptions in connectivity by maintaining the correct pathing information for the host systems accessing the LUN.
For more details, refer to:
* NetApp Documentation on LUN Management
質問 # 39
When using FCP, what is the minimum number of FC switches needed to redundantly attach three ESXi hosts?
- A. 0
- B. 1
- C. 2
- D. 3
正解：A
解説：
When using Fibre Channel Protocol (FCP), the minimum number of FC switches needed to redundantly attach three ESXi hosts is 2. This setup ensures that each host has multiple paths to the storage, providing high availability and fault tolerance. Each ESXi host should be connected to both switches, allowing for continuous operation even if one switch fails.
For more information, refer to:
* NetApp Documentation on FC Switch Configurations
* NetApp Community Discussion on Redundant FC Setup
質問 # 40
An administrator finishes an installation of a new NetApp ASA system at the customer site and creates a new LUN. The customer wants to restrict the access of the LUN to specific UFs.
Where would the administrator configure this?
- A. Portset
- B. Zoning
- C. Selective LUN Map
- D. igroup
正解：D
解説：
To restrict access to a newly created LUN to specific hosts, the administrator should configure theigroup (initiator group). An igroup is used to control which initiators (hosts) are allowed to access specific LUNs.
This ensures that only authorized hosts can access the storage, enhancing security and access control.
For more details, refer to:
* NetApp Documentation on iGroups (NetApp).
質問 # 41
A customer wants to enable CHAP authentication on their iSCSI sessions.
Which command should be used to set up the appropriate security policies and passwords?
- A. security login create
- B. security certificate create
- C. vserver iscsi security create
- D. igroup initiator modify
正解：C
解説：
To enable CHAP (Challenge-Handshake Authentication Protocol) authentication on iSCSI sessions, the command vserver iscsi security create should be used. This command sets up the necessary security policies and passwords required for CHAP authentication, ensuring secure access to iSCSI targets.
For more details, refer to:
* NetApp Documentation on iSCSI Configuration (NetApp).
質問 # 42
What needs to be done to create a consistent Snapshot copy of a LUN without disruptions?
- A. Map the LUN to a host.
- B. Ensure that the LUN is the only one in the volume.
- C. Quiesce I/O to the LUN.
- D. Ensure that the LUN Is unmapped from the host.
正解：C
解説：
To create a consistent Snapshot copy of a LUN without disruptions, it is necessary to quiesce I/O to the LUN.
This process involves pausing or temporarily stopping the input/output operations to ensure that the data is in a consistent state when the snapshot is taken. This method is crucial for maintaining data integrity and consistency in the snapshot.
For further details, refer to:
* NetApp Documentation on Snapshot Consistency
* NetApp Best Practices for Snapshot Management
質問 # 43
What connectivity Is required between NetApp ONTAP clusters in order to configure SnapMirror active sync across two data centers for FC?
- A. Dedicated IP switches and ISL
- B. Shared FC switches
- C. Cluster peering
- D. Cedicated FC switches and ISL
正解：C
解説：
To configure SnapMirror active sync across two data centers using FC (Fibre Channel), the required connectivity between NetApp ONTAP clusters is cluster peering. Cluster peering involves establishing a trust relationship between the clusters, allowing them to replicate data seamlessly. This setup ensures that data synchronization and disaster recovery processes are effective and reliable.
For more detailed information, you can check:
* NetApp Documentation on SnapMirror and Cluster Peering
質問 # 44
Which two steps must be taken first to restore a LUN from a SnapMirror Synchronous destination? (Choose two.)
- A. Initialize the relationship.
- B. Delete the relationship.
- C. Release the relationship.
- D. Resync the relationship.
正解：B、C
解説：
To restore a LUN from a SnapMirror Synchronous destination, the following steps must be taken:
* Release the relationship: This step is necessary to break the SnapMirror relationship, allowing the LUN to be restored independently.
* Delete the relationship: After releasing the relationship, deleting it ensures that there are no residual dependencies or configurations that might interfere with the restore process.
For more information, refer to:
* NetApp Documentation on SnapMirror Synchronous (NetApp) (NetApp).
質問 # 45
During maintenance of A NetApp AFF ONTAP cluster, which two steps are needed to move the SAN UFs to new nodes that are members of a portset? (Choose two.)
- A. Disable the zoning of the LIF WWPN.
- B. Remove the LIF from the portset.
- C. Disable the SLM feature for the node that hosts the LIF.
- D. Take the SAN LIF offline.
正解：B、D
解説：
To move SAN LIFs to new nodes that are members of a portset during maintenance of a NetApp AFF ONTAP cluster, you should take the following steps:
* Remove the LIF from the portset: This ensures that the LIF is no longer associated with the current node, preparing it for the move to the new node.
* Take the SAN LIF offline: This step is necessary to make configuration changes without causing disruption to the SAN hosts. Once offline, the LIF can be moved to the new node and reconfigured as needed.
These actions help maintain the integrity and performance of the SAN environment during the migration of LIFs.
For more details, see:
* NetApp Documentation on Moving SAN LIFs
* NetApp Community on Moving LIFs
質問 # 46
A storage administrator recently implemented ISCSI SAN in a customer environment. Which two actions should be done to ensure the best performance? (Choose two.)
- A. Configure Jumbo frames In the entire data path.
- B. Zone the host by using the host WWPNs.
- C. Decrease the default queue depth on the host to eight.
- D. Connect host and storage ports to the same switches.
正解：A、D
解説：
To ensure the best performance in an iSCSI SAN implementation:
* Connect host and storage ports to the same switches: This minimizes latency and maximizes the efficiency of data paths by ensuring direct connections within the same network segment.
* Configure Jumbo frames in the entire data path: Setting a larger Maximum Transmission Unit (MTU) size reduces the overhead for processing each packet, thus improving overall network performance. Ensuring Jumbo frames are configured end-to-end in the data path is crucial for optimal
* performance.
For further details, check:
* NetApp Best Practices for iSCSI
* NetApp Community Discussion on iSCSI Performance
質問 # 47
An administrator runs the lun igroup show -insrar.ee command on a NetApp ONTAP SAN.
Based on the output, what is the initiator type?
- A. IQN
- B. WWPN
- C. NQN
- D. WWNN
正解：B
解説：
Based on the output of the command lun igroup show -instance, which lists the protocol as fcp and the initiator as server1.netapp.com, the initiator type is WWPN (World Wide Port Name). In Fibre Channel Protocol (FCP) environments, WWPNs are used to uniquely identify Fibre Channel devices. This contrasts with IQNs used in iSCSI, and NQNs used in NVMe over Fabrics.
For more details, refer to:
* NetApp Documentation on Initiators
質問 # 48
A four-node NetApp ONTAP SAN cluster has been deployed. After installation, the engineer wants to verify cabling.
Which NetApp tool should the engineer use?
- A. NetApp Host Utilities package
- B. Hardware Universe
- C. Interoperability Matrix Tool
- D. Active IQ Config Advisor
正解：D
解説：
To verify the cabling of a four-node NetApp ONTAP SAN cluster after installation, the recommended tool is Active IQ Config Advisor. This tool provides detailed checks for proper configuration, including cabling verification, and helps ensure that best practices are followed for optimal performance and reliability.
For further details, see:
* NetApp Active IQ Config Advisor
質問 # 49
A customer Is setting up a four-node NetApp AFF cluster for use with NVMe/TCP and wants to use automatic host discovery.
Which protocol is used for the discovery of controllers?
- A. PXE
- B. mDNS
- C. TFTP
- D. LLDP
正解：B
解説：
For automatic host discovery in a four-node NetApp AFF cluster using NVMe/TCP, the protocol used is mDNS (Multicast DNS). mDNS allows for the discovery of controllers and other networked devices without the need for a centralized DNS server, simplifying the setup process in environments that support NVMe over TCP.
For further information, refer to:
* NetApp Documentation on NVMe/TCP
* NetApp Community on Host Discovery
質問 # 50
A healthcare customer wants to Implement an FC SAN solution consisting of a NetApp ONTAP system, Broadcom switches, and servers.
Which tool contains detailed blueprints and implementation references that can be used to design this solution?
- A. NetApp Active IQ Config Advisor
- B. NetApp Active IQ Unified Manager
- C. NetApp Fusion
- D. NetApp Verified Architecture
正解：D
解説：
The correct tool for designing an FC SAN solution consisting of a NetApp ONTAP system, Broadcom switches, and servers is the "NetApp Verified Architecture" (NVA). The NetApp Verified Architecture provides comprehensive blueprints and detailed implementation references. These blueprints are thoroughly tested, prescriptive in nature, and designed to minimize deployment risks and accelerate time to market. They are specifically designed to help ensure that the architecture meets the high standards required for enterprise environments.
NVA documents include design guides, best practices, and detailed configuration steps, making them invaluable for planning and deploying complex solutions like the one described.
For more information, you can refer to the official NetApp documentation on NetApp Verified Architectures:
* NetApp Verified Architecture Program Summary
* NetApp Verified Architecture Overview
These resources provide detailed insights into the architecture, including technology requirements, deployment procedures, and additional references for further reading.
質問 # 51
A customer requires multiple SAN and NAS protocols on a NetApp AFF cluster. The cluster must concurrently serve a namespace over NVMe/FC, a LUN over FCP, a LUN over iSCSI, and an NFS export.
Based on these requirements, what is the minimum data SVM count that is required?
- A. 0
- B. 1
- C. 2
- D. 3
正解：D
解説：
To concurrently serve a namespace over NVMe/FC, a LUN over FCP, a LUN over iSCSI, and an NFS export, only one data SVM (Storage Virtual Machine) is required. NetApp ONTAP allows a single SVM to supportmultiple SAN and NAS protocols simultaneously, enabling efficient and consolidated management of storage resources.
For more information, refer to:
* NetApp Documentation on SVM Configuration
* NetApp SVM Best Practices
質問 # 52
A storage engineer is required to provide NetApp site design documentation to show that the NetApp ONTAP SAN solution was delivered as intended.
Which NetApp tool can the storage engineer use to automate the creation of a difference report?
- A. Harvest
- B. NetAppDocs
- C. Active IQ Config Advisor
- D. Active IQ OneCollect
正解：D
解説：
Active IQ OneCollect is a NetApp tool designed to collect configuration and performance data from your storage environment, including SAN solutions. It can automate the creation of difference reports by capturing the current state of the system and comparing it against a baseline, thereby showing any changes or deviations from the intended design.
For further details, refer to:
* NetApp Active IQ OneCollect Documentation
質問 # 53
A customer has data in a LUN on an existing third-party SAN storage system that will be migrated to a new NetApp AFF A400 all-flash MetroCluster system. The host connected to the LUN is a Windows Server 2019 system.
In this scenario, which two methods are supported? (Choose two.)
- A. SnapMirror Business Continuity
- B. Client-side copy of the data
- C. Foreign LUN Import in online mode
- D. Foreign LUN Import in offline mode
正解：C、D
解説：
To migrate data from a LUN on an existing third-party SAN storage system to a new NetApp AFF A400 all-flash MetroCluster system, the supported methods include:
* Foreign LUN Import in online mode: This method allows for data migration without significant downtime, enabling the system to continue serving data while the migration process is ongoing.
* Foreign LUN Import in offline mode: This method involves taking the LUN offline during the migration process, which may be necessary in certain scenarios to ensure data integrity.
For more details, refer to:
* NetApp Documentation on Foreign LUN Import
* NetApp Community on LUN Import Methods
質問 # 54
When using tagged VLANs on Cisco Nexus switches for NVMe over TCP, which two changes must be made to enable jumbo frames? (Choose two.)
- A. Modify the Cisco Nexus switches to use an MTU of 9000.
- B. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9000.
- C. Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216.
- D. Modify the Cisco Nexus switches to use an MTU of 9216.
正解：C、D
解説：
For enabling jumbo frames on Cisco Nexus switches for NVMe over TCP with tagged VLANs, the following changes are required:
* Modify the Cisco Nexus switches to use an MTU of 9216: Setting the MTU to 9216 ensures that the network can handle jumbo frames, reducing the number of packets needed for large data transfers and thus improving performance.
* Modify the appropriate broadcast domain in NetApp ONTAP software to use an MTU of 9216:
This setting must match the network configuration to ensure end-to-end support for jumbo frames, which is essential for optimizing performance in NVMe over TCP environments.
For additional information, refer to:
* NetApp Documentation on NVMe over TCP
* Cisco Documentation on Jumbo Frames
質問 # 55
A customer wants to Implement a NetApp AFF system at a small remote site that has two ESXi servers that require SAN storage from the NetApp ONTAP based storage system. The servers will be directly connected, because the customer does not want to deploy any switches.
Which protocol should the customer use?
- A. FCP
- B. FCoE
- C. NFS
- D. iSCSI
正解：D
解説：
For a small remote site with two ESXi servers requiring SAN storage and no switches, the recommended protocol isiSCSI. iSCSI allows for direct connectivity between the servers and the NetApp ONTAP storage system using standard Ethernet infrastructure, which is suitable for environments without Fibre Channel switches.
For more information, see:
* NetApp iSCSI Configuration Guide
質問 # 56
On a two-node NetApp AFF ASA cluster, what is the recommended minimum number of paths for a SAN environment from the client host perspective?
- A. 0
- B. 1
- C. 2
- D. 3
正解：B
解説：
In a two-node NetApp AFF ASA cluster, the recommended minimum number of paths for a SAN environment from the client host perspective is 4. This configuration ensures high availability and load balancing, which are critical for maintaining performance and resilience in a SAN environment. Each host should have at least two paths to each controller to achieve this setup.
For more detailed information, you can refer to:
* NetApp SAN Configuration
* NetApp All-Flash SAN Array Documentation
質問 # 57
An SVM is created for FCP traffic. LUNs must be created to share with ESXi hosts for datastores. Which two items must be configured after the LUN is created, for this to happen? (Choose two.)
- A. Create an igroup with the ESXi hosts' WWPNs.
- B. Configure CHAP authentication.
- C. Create an igroup with the ESXi hosts' WWNNs.
- D. Map the LUNs to the igroup.
正解：A、D
解説：
For configuring LUNs to share with ESXi hosts for datastores in an SVM created for FCP traffic, the following steps are necessary after creating the LUN:
* Create an igroup with the ESXi hosts' WWPNs: This step involves defining an initiator group that includes the WWPNs of the ESXi hosts that need access to the LUN.
* Map the LUNs to the igroup: This step assigns the LUN to the created igroup, allowing the ESXi hosts to access the LUN.
For further details, refer to:
* NetApp Documentation on LUN and igroup Configuration
質問 # 58
A storage administrator wants to increase security and optimize performance in a recently implemented SAN deployment.
What should the storage administrator configure to ensure initiator restriction to certain LIFs?
- A. Subnets
- B. Access list
- C. Network route
- D. Broadcast domain.
正解：B
解説：
To increase security and optimize performance in a SAN deployment, configuring an access list is essential.
Access lists restrict initiator access to specific LIFs, ensuring that only authorized hosts can connect to the storage system. This helps in enhancing security by preventing unauthorized access and optimizes performance by controlling and managing the paths used for storage access.
For additional details, you can refer to:
* NetApp SAN Administration Guide
質問 # 59
What Is a recommended setting for using the NetApp ONTAP LUN fractional reserve?
- A. Space allocation is set to enable.
- B. Space guarantee is set to volume.
- C. LUN space reservation is disabled.
- D. Volume Snapshot copy automatic deletion is disabled.
正解：B
解説：
The recommended setting for using the NetApp ONTAP LUN fractional reserve is to set the space guarantee to "volume". This setting ensures that the required space for overwrites in the volume is reserved, preventing potential write failures when snapshot copies are created. This setup helps in maintaining the performance and reliability of the storage system by ensuring there is always enough space allocated for the LUN.
For further details, you can refer to:
* NetApp Community Discussion on Fractional Reserve
* NetApp Documentation on Space Management
質問 # 60
A LUN Is displaying 90% used space in the NetApp ONTAP CLI, but a Windows Server shows only 10% used space.
What is the first step to take to address this issue?
- A. Disable space allocation.
- B. Enable space allocation.
- C. Disable automatic resizing.
- D. Enable automatic resizing.
正解：B
解説：
When a LUN shows 90% used space in the NetApp ONTAP CLI but a Windows Server shows only 10% used space, the discrepancy is often due to how space allocation is handled between the two systems. Enabling space allocation ensures that the ONTAP system accurately reflects the actual space usage as reported by the host system, in this case, the Windows Server. This adjustment allows ONTAP to reclaim and manage space more effectively, aligning the reported usage between the ONTAP system and the host.
For more information, refer to:
* NetApp Community Discussion on Space Allocation
* NetApp Documentation on Space Usage
質問 # 61
During expansion planning for a 10-node cluster running NetApp ONTAP 9.14.1 software, which uses SAN and NAS, how many additional nodes can be added to this cluster?
- A. 0
- B. 1
- C. 2
- D. 3
正解：C
解説：
NetApp ONTAP 9.14.1 supports up to a 16-node cluster for SAN and NAS configurations. Given a current
10-node cluster, you can add up to 6 additional nodes to reach the maximum supported node count. This expansion capability ensures scalability for growing storage needs while maintaining high availability and performance.
For more information, refer to:
* NetApp Storage Limits Documentation (NetApp)
質問 # 62
......
検証済み材料を使うならまずNS0-521テストエンジンを試そう：https://www.jpntest.com/shiken/NS0-521-mondaishu
合格するに必要な問題集はNS0-521試験：https://drive.google.com/open?id=11c0yAoIND4yzU-2XzGsYkZQnbMkMvQzf