NS0-592無料問題集「Network Appliance NetApp Certified Support Engineer, ONTAP Specialist」

質問 1

The root aggregate on your single-node ONTAP cluster failed. You have the configuration backups saved on your FTP server?
In this scenario, which two steps are part of the recovery procedure? (Choose two.)

（A）Create a new root aggregate and set its ha_policy option to cfo.

（B）Perform a Netboot using the configuration backup.

（C）Create a new aggregate and set its ha_policy option to sfo.

（D）Boot into maintenance mode.

正解：A、D 解答を投票する

質問 2

You migrated from a FAS3250 system to a new A200 system. After the migration, you notice that data compaction fails to be enabled on the migrated volumes.
In this scenario, which statement is correct?

（A）You need to schedule background deduplication on all volumes.

（B）You need a license to have full efficiency on AFF systems.

（C）Data compaction is not supported on the A200 system.

（D）The volumes are thick-provisioned.

正解：D 解答を投票する

質問 3

A new cluster running ONTAP 9.5 has just been installed and you want to create a FlexGroup volume. Which action will accomplish this task?

（A）Use the storage pool create command.

（B）Use the Deploy utility to provision the FlexGroup volume.

（C）Use the volume create command.

（D）Use the volume size command.

正解：A 解答を投票する

質問 4

Click the exhibit button.

A storage administrator reports that when they enabled Vscan, they began receiving reports of CIFS users having very slow access to all their files. The storage administrator recovered from the issue by disabling Vscan on their SVM. The storage administrator was able to collect perfstat output during the time of the reported slow access, as shown in the exhibit.
In this situation, what is the problem?

（A）The problem was with both Vscan servers 192.168.100.144 and 10.23.23.54.

（B）Vscan server 10.23.23.54 was slower than Vscan server 192.168.100.144 in completing Vscan requests.

（C）The problem is on the SVM, as shown in the scan_latency output.

（D）Vscan server 192.168.100.144 was slower than Vscan server 10.23.23.54 in completing Vscan requests.

正解：D 解答を投票する

質問 5

Your customer has initiated several volume move commands to redistribute the workload in their 8-node cluster. To verify that this process is not affecting their client access, they were monitoring the network switches that provide client access, but they do not see the network load of the volume move command.
In this scenario, what is the reason for the behavior?

（A）The volume move command uses copy offload protocol, so it does not show up when monitored.

（B）The volume move command uses the cluster interconnect switches, not the client access switches.

（C）The volume move command uses the intercluster LIFs, not the data LIFs.

（D）The volume move command uses the HA iWarp interconnect, not the client access switches.

正解：A 解答を投票する

質問 6

At a customer site, the storage failover giveback command fails when giving back the root aggregate.
What would be two reasons for this failure? (Choose two.)

（A）There are active NFS connections.

（B）The HA interconnect is not operational.

（C）There are failed disks.

（D）There are active SIS operations running.

正解：B、C 解答を投票する

質問 7

Click the exhibit button.

A customer notifies you that Active IQ is showing a warning that a broadcast domain in their environment has been configured with ports from multiple VLANs.
Referring to the exhibit, which two statements are correct? (Choose two.)

（A）You should move the e0M ports to a Broadcast Domain that is dedicated to only management traffic.

（B）You should configure e0M so that is tagged on VLAN 40.

（C）A VLAN tag cannot be assigned to the e0M port, so the configuration is acceptable.

（D）You should change the LIF service policy to net-intercluster to prevent the LIFs from failing over to the e0M ports.

正解：B、D 解答を投票する

NS0-592 無料問題集「Network Appliance NetApp Certified Support Engineer, ONTAP Specialist」

弊社を連絡する

関連リンク

トップ試験