DES-4121無料問題集「EMC Specialist - Implementation Engineer, PowerEdge」

質問 1

What are benefits of installing the Dell iDRAC Service Module?

（A）Remote iDRAC reset
Ability to update firmware on the server

（B）In-band SNMP traps tor Hardware alerts
Remote iDRAC reset

（C）iDRAC access via host OS
Ability to access the Lifecycle Controller tor server updates

（D）Ability to update firmware on the server
iDRAC access via host OS

正解：B 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 2

A technician is setting up a previously used server. Upon power up the PERC alerts them to the presence of a foreign configuration in the iDRAC storage section. The technician checks Foreign View the foreign array configuration is the same as the configuration needed for the new project. What is a recommended way to prepare the disks for the new project?

（A）Access the Ctrl-R utility, cleat the foreign configuration and set up array as needed

（B）Format the foreign configuration and clear the controller configuration

（C）Import the foreign configuration and perform a full initialization

（D）Edit the foreign configuration and set it to Ready

正解：A 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 3

A technician is on-site to update firmware on a server lot which the iDRAC is not configured in addition, the technician does not have access to the OS. However, the site does have DHCP available on the production network as well as on an available workstation The technician has access to the rack-mounted KVM How should the technician update the firmware on the server?

（A）Log in via SSH through a serial cable and configure the workstation as a proxy, then download the firmware

（B）Log in via telnet through a serial cable and configure the workstation as a proxy, then download the firmware

（C）Reboot the server, select F2, configure the network, and run Firmware Update

（D）Reboot the server, select F10, configure the network, and run Firmware Update

正解：D 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 4

A technician plugs in a sever that has dual power supply units. After powering on the system, they notice that the power supply status indicators blink green then turn. What troubleshooting stops should the technician take to resolve this issue?

（A）Check that the PSUs ate not connected to a 240VAC source

（B）Update the iDRAC firmware to enable control of new PSU features

（C）Check that the PSUs are the same efficiency, feature set, health status, and supported voltage

（D）Set the power supply redundancy option to No Redundancy

正解：C 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 5

A technician needs to remotely update the iDRAC with Lifecycle Controller firmware. They have downloaded the latest iDRAC firmware to the management station and connected to the iDRAC GUI.
What slop is required to complete the update?

（A）Boot the server into F 10 to start the firmware update

（B）Go to Summery Pago and reset the ORAC

（C）After firmware update completes, restart server

（D）Go to the Firmware Update pad and upload the iDRAC firmware

正解：B 解答を投票する

質問 6

A technician deletes the iDRAC Express license on a R440 server. Which license type is then enabled?

（A）iDRAC will not have a license until a new one is installed

（B）iDRAC Enterprise license

（C）iDPAC Express license cannot be deleted

（D）iDRAC Base license

正解：D 解答を投票する

DES-4121 無料問題集「EMC Specialist - Implementation Engineer, PowerEdge」

弊社を連絡する

関連リンク

トップ試験