Cisco 300-410試験問題集にはPDF問題とテストエンジンを試せ！
最新300-410試験問題集には合格保証付きます
質問 # 143
Refer to the exhibit.
Which two actions should be taken to access the server? (Choose two.)
- A. Add a floating static route to reach to 192.168.2.2 with administrative distance higher than OSPF
- B. Modify the access list to add a second line of permit ip any
- C. Add a sequence 20 in the route map to permit access list 1.
- D. Modify the access list to deny the route to 192.168.2.2.
- E. Modify distribute list seq 10 to permit the route to 192.168.2.2.
正解：A、D
質問 # 144
How is VPN routing information distributed in an MPLS network?
- A. It is controlled using of VPN target communities.
- B. It is controlled through the use of RD.
- C. The top level of the customer data packet directs it to the correct CE device
- D. It is established using VPN IPsec peers.
正解：A
解説：
Route Targets (BGP extended communities) on PE routers dictate which VRFs import or export VPN routes, thereby controlling the distribution of VPN routing information over the MPLS backbone.
質問 # 145
Drag and drop the descriptions from the left onto the corresponding MPLS components on the right.
正解：
解説：
質問 # 146
Which BGP attribute can be used to influence the path that incoming traffic takes into your AS from other Autonomous Systems?
- A. Local Preference
- B. AS_Path
- C. Weight
- D. Metric manipulation
正解：B
質問 # 147 
Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
- A. Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command
- B. Enable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command
- C. Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface.
- D. Disable IPv6 on the E 0/0 interface using the no ipv6 enable command
正解：A
解説：
Once again, Cisco changed the IOS configuration commands required for OSPFv3 configuration. The new OSPFv3 configuration uses the "ospfv3" keyword instead ofthe earlier "ipv6 router ospf" routing process command and "ipv6 ospf" interface commands.
The Open Shortest Path First version 3 (OSPFv3) address families feature enables both IPv4 and IPv6 unicast traffic to be supported. With this feature, users may havetwo processes per interface, but only one process per address family (AF).
質問 # 148
Refer to the exhibit. The IT manager received reports from users about slow application through
network x. Which action resolves the issue?
- A. Increase the bandwidth from the service provider.
- B. Move the servers into the users subnet.
- C. Use the variance 2 command to enable load balancing.
- D. Upgrade the IOS on router E.
正解：C
質問 # 149
Refer to the exhibit.
The R1 and R2 configurations are:
The neighbor is not coming up. Which two sets of configurations bring the neighbors up? (Choose two.)
- A. R2ip route 10.1.1.1 255.255.255.255 192.168.1.1#router bgp 200neighbor 10.1.1.1 tti-security hops
1neighbor 10.1.1.1 update-source loopback 0 - B. R1ip route 10.1.1.2 255.255.255.255 192.168.1.2#router bgp 100neighbor 10.1.1.1 ttl-security hops
1neighbor 10.1.1.2 update-source loopback 0 - C. R2ip route 10.1.1.2 255.255.255.255 192.168.1.2#router bgp 100neighbor 10.1.1.2 ttl-security hops
1neighbor 10.1.1.2 update-source loopback 0 - D. R2ip route 10.1.1.1 255.255.255.255 192.168.1.1#router bgp 200neighbor 10.1.1.1 disable-connected- checkneighbor 10.1.1.1 update-source loopback 0
- E. R1ip route 10.1.1.2 255.255.255.255 192.168.1.2#router bgp 100neighbor 10.1.1.2 disable-connected- checkneighbor 10.1.1.2 update-source Loopback0
正解：D、E
解説：
Disable-connected-check enables a directly connected eBGP neighbor to peer using a loopback address without adjusting the default TTL of 1. In disable connected check the router does not decrease the TTL of an IP packet that is destined to itself so it only counts or considers as one hop between the two loopbacks of the routers.
質問 # 150
Which label operations are performed by a label edge router?
- A. PUSH and POP
- B. SWAP and PUSH
- C. SWAP and POP
- D. PUSH and PHP
正解：A
解説：
Explanation
A label edge router (LER, also known as edge LSR) is a router that operates at the edge of an MPLS network and acts as the entry and exit points for the network. LERs push an MPLS label onto an incoming packet and pop it off an outgoing packet.
質問 # 151
Refer to the exhibit. An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the summary route does not show up in the routing table.
Why is the summary route missing?
- A. The summary route is visible only in the OSPF database, not in the routing table.
- B. The summary route is not visible on this router, but it is visible on other OSPF routers in the same area.
- C. There is no route for a subnet inside 10.0.0.0/8, so the summary route is not generated.
- D. The summary-address command is used only for summarizing prefixes between areas.
正解：C
解説：
Section: Layer 3 Technologies
質問 # 152
How is the LDP router ID used in an MPLS network?
- A. The MPLS LDP router ID must match the IGP router ID.
- B. The force keyword changes the router ID to the specified address without causing any impact.
- C. The loopback with the highest IP address is selected as the router ID.
- D. If not configured, the operational physical interface is chosen as the router ID even if a loopback is configured.
正解：C
質問 # 153 
Refer to the exhibit. A network engineer is provisioning end-to-end traffic service for two different enterprise networks with these requirements The OSPF process must differ between customers on HQ and Branch office routers, and adjacencies should come up instantly.
The enterprise networks are connected with overlapping networks between HO and a branch office Which configuration meets the requirements for a customer site?
A
- A.
- B.
- C.
- D.
正解：B
質問 # 154
An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency. The output of the show ip ospf neighbor command shows that the neighbor state is EXSTART/EXCHANGE.
Which action should be taken to resolve this issue?
- A. match the passwords
- B. match the MTUs
- C. match the network types
- D. match the hello timers
正解：B
解説：
Explanation
質問 # 155
Refer to the exhibit.
A network administrator is using the DNA Assurance Dashboard panel to troubleshoot an OSPF adjacency that failed between Edge_NYC interface GigabitEthernet1/3 with Neighbor Edge_SNJ. The administrator observes that the neighborship is stuck in exstart state. How does the administrator fix this issue?
- A. Configure to match the OSPF interface MTU settings on both routers.
- B. Configure to match the OSPF interface unique IP address and subnet mask on both routers.
- C. Configure to match the OSPF interface network types on both routers.
- D. Configure to match the OSPF interface speed and duplex settings on both routers.
正解：A
解説：
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13684-12.html
質問 # 156
Refer to the exhibit. A network engineer finds that PC1 is accessing the hotel website to do the booking but fails to make payment. Which action resolves the issue?
- A. Increase the AD to 200 of static route 192.168.94.0 on R3.
- B. Configure a reverse route on R1 for PC1 172.16.1.0/24.
- C. Decrease the AD to 5 OSPF route 192.168.94.0 on R1.
- D. Allow stub network 10.10.202.168/30 on router R3 OSPF.
正解：B
質問 # 157
Refer to the exhibit.
An engineer receives this error message when trying to access another router m-band from the serial interface connected to the console of R1. Which configuration is needed on R1 to resolve this issue?
- A. Option B
- B. Option D
- C. Option A
- D. Option C
正解：B
解説：
Explanation
https://community.cisco.com/t5/other-network-architecture/out-of-band-router-access/td-p/333295
質問 # 158 
Refer to the exhibit. An engineer examines the BGP update for the IPv6 prefix 2001:db8::1/128. which should have been summarized into a /64 prefix. Which sequence of actions achieves the summarization?
- A. R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to the same AS. Configure an aggregate address on the router with ID 3 3.3.3 for the prefix.
- B. R1 is a route reflector with a router ID of 1.111. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
- C. R1 is a route reflector client of a RR with a router ID of 1.1.1.1. and the originator of the prefix has a router ID of 3.3.3.3. Both routers belong to different ASs. The prefix is not advertised to any peer and must be advertised using the network statement on R3.
- D. R1 is a route reflector with a router ID of 3.3.3.3. and the originator of the prefix is a route reflector client, which has a router ID of 3.3.3.3. Both routers belong to the same AS Configure an aggregate address on the router with ID 1.1.1.1 for the prefix
正解：A
質問 # 159 
Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?
- A. Option B
- B. Option D
- C. Option A
- D. Option C
正解：B
質問 # 160
Refer to the exhibit.
An engineer configured BGP between routers R1 and R3 The BOP peers cannot establish neighbor adjacency to be able to exchange routes. Which configuration resolves this issue?
- A. R1router bgp 6501address-family ipv6neighbor AB01:2011:7:100;:3 activate
- B. R3router bgp 6502address-family ipv6neighbor AB01:2011:7:100::1 activate
- C. R3router bgp 6502neighbor AB01:2011:7:100::1 ebgp-muttlhop 255
- D. R1router bgp 6501 neighborAB01:2011:7:100::3ebgp-multihop255
正解：B
解説：
From the output, we learned that R1 was trying to establish BGP neighbor relationship with R3 but failed.
Both of them were using physical interface to establish neighbor relationship so wedon't need the "... ebgp- multihop" command here. The only reasonable answer is R3 has not been configured to activate BGP neighbor relationship with R1.
質問 # 161
Refer to the exhibit.
The network administrator configured redistribution on an ASBR to reach to all WAN networks but failed Which action resolves the issue?
- A. The route map EIGRP->OSPF must have the 10.0.106.0/24 entry to exist in one of the three prefix lists to pass
- B. EIGRP must redistribute the 10.0.106.0/24 route instead of using the network statement
- C. The OSPF process must have a metric when redistributing prefixes from EIGRP.
- D. The route map must have the keyword prefix-list to evaluate the prefix list entries
正解：D
解説：
In order to use a prefix-list in a route-map, we must use the keyword "prefix-list" in the "match" statement. . For example:
match ip address prefix-list WAN_PREFIXES
Without this keyword, the router will try to find an access-list with the same name instead.
質問 # 162
During the maintenance window an administrator accidentally deleted the Telnet-related configuration that permits a Telnet connection from the inside network (Eth0/0) to the outside of the networking between Friday - Sunday night hours only. Which configuration resolves the issue?
- A.
- B.
- C.
- D.
正解：C
質問 # 163
The network administrator configured the router for Control Plane Policrg so that inbound SSH traffic is policed to 500 kbps This policy must apply to traffic coming in from 101010 0<24 and 192 168 10.0/24 networks
The Control Rane Policing is not applied to SSH traffic and SSH is open to use any bandwidth available.
Which configuration resolves this issue?
- A.
- B.
- C.
- D.
正解：D
質問 # 164
......
Cisco 300-410試験は、エンタープライズネットワークでの高度なルーティングとサービスの実装に焦点を当てた認定試験です。この試験は、ネットワークインフラストラクチャとルーティングの専門知識を向上させたいITプロフェッショナルの知識とスキルを試験するために設計されています。この試験に合格することは、複雑なエンタープライズネットワークソリューションを実装する能力を証明したい人にとって、重要な成果です。
信頼できるCCNP Enterprise 300-410問題集PDFには2026年08月28日更新された問題です：https://www.jpntest.com/shiken/300-410-mondaishu
必ず合格できるCisco 300-410試験正確な800問題と解答あります：https://drive.google.com/open?id=1-Mra_dUJ0l12h8hojhEVyTEu1aE4Fyh4