合格させるFortinet NSE6_FWF-6.4試験には保証が付きます。更新されたのは37問があります
最新のNSE6_FWF-6.4合格保証付き試験問題集の認定サンプル問題
質問 # 14
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Enable frequency handoff on the AP to band steer clients
- B. Increase the transmission power of the AP radios
- C. Reduce the number of wireless networks being broadcast by the AP
- D. Install another AP in the reception area to improve available bandwidth
正解：B
質問 # 15
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Disable intra-vap-privacy for the Authors vap-wireless network
- B. For both interfaces in the wtp-profile, configure vap-all to be manual
- C. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- D. Increase the transmission power of the AP radio interfaces
正解：A、B
質問 # 16
What type of design model does FortiPlanner use in wireless design project?
- A. Analytical model
- B. Integration model
- C. Predictive model
- D. Architectural model
正解：D
解説：
FortiPlanner will look familiar to anyone who has used architectural or home design software.
質問 # 17
How are wireless clients assigned to a dynamic VLAN configured for hash mode?
- A. Using the current number of wireless clients connected to the SSID and the group the FortiAP is a member of
- B. Using the current number of wireless clients connected to the SSID and the number of IPs available in the least busy VLAN
- C. Using the current number of wireless clients connected to the SSID and the number of VLANs available in the pool
- D. Using the current number of wireless clients connected to the SSID and the number of clients allocated to each of the VLANs
正解：C
解説：
VLAN from the VLAN pool based on a hash of the current number of SSID clients and the number of entries in the VLAN pool.
質問 # 18
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. DHCP
- B. Static
- C. Broadcast
- D. Multicast
正解：A
質問 # 19
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user usage stats
- B. Provides real-time insight into user movements
- C. Provides real-time insight into user online activity
- D. Provides real-time insight into user purchase activity
正解：B
解説：
Explanation
(Page 88 Study Guide) "FortiPresence provides data and analytics based on demographic segmentation and visitor movement between areas" According to the web search results, FortiPresence location map functionality provides real-time insight into user movements. It uses the location data from the Fortinet access points to detect each visitor's smartphone Wi-Fi signal and track their location and behavior within the site. It also provides data visualization in a customizable format, such as heat maps and animated flows, to show the visitor traffic and movement patterns.
This geographical data analysis can help improve visitor experiences and business outcomes.
References: Location Analytics | FortiPresence 22.4.0 - Fortinet Documentation, FortiPresence Data Sheet
質問 # 20
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?
- A. The new network must be manually assigned to a FortiAP profile.
- B. Security Fabric and HTTPS must be enabled on the wireless network interface
- C. The wireless network to Internet firewall policy must be configured
- D. The wireless network interface must be assigned a Layer 3 address
正解：C
解説：
A FortiGate unit is an industry leading enterprise firewall. In addition to consolidating all the functions of a network firewall, IPS, anti-malware, VPN, WAN optimization, Web filtering, and application control in a single platform, FortiGate also has an integrated Wi-Fi controller.
質問 # 21
Which factor is the best indicator of wireless client connection quality?
- A. The channel utilization of the channel the client is using
- B. Downstream link rate, the connection rate for the AP to the client
- C. The receive signal strength (RSS) of the client at the AP
- D. Upstream link rate, the connection rate for the client to the AP
正解：C
解説：
SSI, or "Received Signal Strength Indicator," is a measurement of how well your device can hear a signal from an access point or router. It's a value that is useful for determining if you have enough signal to get a good wireless connection.
質問 # 22
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- B. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- C. DARRP measurements can be scheduled to occur at specific times.
- D. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
正解：A、C
解説：
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
質問 # 23
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- B. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- C. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
- D. Areas with the signal strength weaker than -68 dB are cut out of the map
正解：B
質問 # 24
As a network administrator, you are responsible for managing an enterprise secure wireless LAN. The controller is based in the United States, and you have been asked to deploy a number of managed APs in a remote office in Germany.
What is the correct way to ensure that the RF channels and transmission power limits are appropriately configured for the remote APs?
- A. Create a new FortiAP profile and change the county code settings on the profile
- B. Configure the APs individually by overriding the settings in Managed FortiAPs
- C. Clone a suitable FortiAP profile and change the county code settings on the profile
- D. Configure the controller for the correct country code for Germany
正解：C
質問 # 25
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the AP CLI, using the cw_diag ksta command
- B. On the controller CLI, using the diag wireless-controller wlac -d sta command
- C. On the controller CLI, using the WiFi Client monitor
- D. On the AP CLI, using the cw_diag -d sta command
正解：A
質問 # 26
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Control channels
- B. Security channels
- C. FortLink channels
- D. Data channels
正解：A、D
解説：
Explanation
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
質問 # 27
How can you find upstream and downstream link rates of a wireless client using FortiGate?
- A. On the FortiGate CLI, using the diag wireless-controller wlac -d Sta command
- B. On the FortiAP CLI, using the cw_diag ksta command
- C. On the FortiGate GUI, using the WiFi Client monitor
- D. On the FortiAP CLI, using the cw_diag -d sta command
正解：C
解説：
Explanation
The WiFi Client monitor on the FortiGate GUI shows the upstream and downstream link rates of a wireless client, along with other information such as MAC address, SSID, IP address, signal strength, and connection time. The link rates indicate the maximum data rates that the client can achieve in both directions.
References: Secure Wireless LAN Course Description, page 7; [FortiOS 6.4.0 Handbook - Wireless Controller], page 37.
質問 # 28
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. Wireless network security must be set to open
- B. Two wireless APs must be sending data
- C. SQL services must be running
- D. DTLS encryption on wireless traffic must be turned off
正解：C
質問 # 29
......
Fortinet NSE6_FWF-6.4試験は、ワイヤレスセキュリティとネットワーキングの概念、およびFortinet Wireless Solutionsの実践的な経験を強く理解する必要がある挑戦的な認定試験です。この認定を追求することに関心のあるITの専門家は、Fortinet Technologiesと協力して少なくとも2年の経験があり、Fortinetのセキュリティファブリックに精通している必要があります。
最新NSE6_FWF-6.4テスト材料には有効なNSE6_FWF-6.4テストエンジン：https://www.jpntest.com/shiken/NSE6_FWF-6.4-mondaishu