最新NACE-CIP2-001テスト材料には有効なNACE-CIP2-001テストエンジン
NACE-CIP2-001更新された試験問題集で[2023年最新] 練習には有効な試験問題集
コーティング検査員レベル2の認定を取得するには、候補者は承認されたトレーニングコースを修了し、関連する職務経験を取得するなどの特定の前提条件を満たす必要があります。これらの要件を満たした後、候補者はNACE-CIP2-001認定試験を受験できます。この試験は、筆記試験と実技試験の両方から構成されています。筆記試験は理論知識をカバーし、実技試験は候補者が実際の現場でコーティング検査を行う能力を評価します。試験の両方のコンポーネントに合格すると、候補者は認定を受け、再認定が必要になるまで3年間有効です。
質問 # 18
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. run through the air wash separator.
- B. mixed with uncontaminated abrasive
- C. washed with clean potable water prior to Use.
- D. disposed of properly.
正解:D
質問 # 19
When ASIN D 3363 is specified the Inspector must:
- A. Record the highest value attained
- B. Record the percentage of failure
- C. Record the two end points identified in the standard
- D. Use the correct solvent
正解:C
質問 # 20
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Supervision Costs
- B. Lower Application Costs
- C. Lower Coating Life Cycle Costs
- D. Lower Safety Enforcement Costs
正解:C
質問 # 21
Inspection and Test Plans are provided to:
- A. So the contractor has a single document to reference
- B. To supersede the requirements of the product data sheets
- C. So the Inspector doesn't have to read the entire specification
- D. Outline the inspection steps, sequencing and pass/fail criteria
正解:D
質問 # 22
Corrosion is the reverse process of
- A. flaking.
- B. steel manufacturing.
- C. galvanic deterioration.
- D. hot dipping.
正解:B
質問 # 23
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. provide protection against soil chemicals.
正解:B
質問 # 24
Inspection and Test plans are developed by referencing:
- A. The Specification, Safety Manual, Relevant Standards and Codes
- B. The Specification, TDS, relevant Standards and Codes
- C. The Specification, Application Guidelines, 'Relevant Standards and Codes
- D. The Specification, SDS, relevant Standards and Codes
正解:B
質問 # 25
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Slightly different to air blast cleaning
- B. Comparable to air blast cleaning
- C. Different than air blast cleaning
- D. The same as air blast cleaning
正解:D
質問 # 26
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Preferential fuel for the fire
- C. fire extinguishing characteristics
- D. Explosion resistance
正解:A
質問 # 27
The Inspectors' goal at the Pre-Job Conference is to:
- A. Take accurate meeting minutes for distribution
- B. Obtain a clear understanding of the Specification
- C. Manage the meeting so it doesn't go off topic
- D. Discuss contractual requirements
正解:B
質問 # 28
Surface preparation methods for Non-ferrous metals are:
- A. Specific for each type of Non-ferrous metal
- B. The same for all Non-FetT0us metals
- C. The same as for Ferrous metals
- D. Not required
正解:A
質問 # 29
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Transmission
- C. Distribution
- D. Gathering
正解:C
質問 # 30
A reinforced coating is
- A. equally resistant to movement and impact as a non-reinforced coating.
- B. equally resistant to abrasion and impact as a non-reinforced coating.
- C. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. more resistant to movement, abrasion, and impact than a non-reinforced coating.
正解:D
質問 # 31
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A mechanical adhesion tester
- C. A hardness tester
- D. A destructive paint inspection Tooke gauge
正解:D
質問 # 32
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface cleanliness prior to coating
- B. Contamination levels prior to coating
- C. Compressive and tensile strength prior to coating
- D. Surface profile prior to coating
正解:D
質問 # 33
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Tooke Gauge
- C. Ultra Sonic DFT Gauge
- D. Eddy Current Gauge
正解:B
質問 # 34
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Document the readings at the end of the shift
- C. Advise the coating applicator supervisor of your readings
- D. Check to See if the dehumidification equipment is operating correctly
正解:C
質問 # 35
Coating surveys may include which steps?
Select All That Apply:
- A. Develop a survey plan
- B. Summarize the collected data
- C. Evaluate the coatings performance
- D. Schedule the remedial work
正解:A、B、C、D
質問 # 36
......
NACE-CIP2-001 認定を取得することは、コーティング検査官にとって重要な達成感であり、彼らの知識、スキル、専門的な発展に対する献身を証明します。この認定は、世界の雇用主や業界の専門家に認められ、専門家としてのキャリアの新たな可能性や昇進の機会を開拓することができます。
NACE-CIP2-001サンプルには正確な更新された問題:https://www.jpntest.com/shiken/NACE-CIP2-001-mondaishu