[2023年11月24日] 最新リアルNACE-CIP2-001試験問題集解答
あなたを簡単に合格させるNACE-CIP2-001試験問と正確なCoating Inspector Level 2PDF問題
質問 # 22
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Challenge the supervisor's authority
- B. Defend the previous inspector
- C. Express a willingness to work with the site team and follow the specification
- D. Suggest to the Owner that the supervisor should be removed from site
正解：C
質問 # 23
NACE Standards include:
- A. Material Requirements
- B. a) only
- C. Standard Practices
- D. a) & b)
正解：D
質問 # 24
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cold flow or creep
- B. Cohesion failure
- C. Adhesion failure
- D. Glue failure
正解：A
質問 # 25
The standards defining surface cleanliness achieved by centrifugal blast cleaning are:
- A. Comparable to air blast cleaning
- B. The same as air blast cleaning
- C. Different than air blast cleaning
- D. Slightly different to air blast cleaning
正解：B
質問 # 26
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
正解：A
質問 # 27
All of these are advantages of using repair patches EXCEPT
- A. inert to common acids, alkalis, and solvents.
- B. special tools or equipment are required.
- C. excellent abrasion resistance.
- D. barrier to moisture and corrosion.
正解：B
質問 # 28
A reinforced coating is
- A. equally resistant to movement and impact as a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
正解：C
質問 # 29
An Inspection and Test Plan is required when:
- A. When the Inspector requests one
- B. It is always required
- C. When the Owner specifies one
- D. When the Coating Applicator requests one
正解：B
質問 # 30
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Non-Conductive coatings applied to a conductive metallic substrate
- B. Magnetic coatings applied to a magnetic metallic substrate
- C. Conductive coatings applied to a cementitious substrate
- D. Conductive coatings applied to a magnetic metallic substrate
正解：A
質問 # 31
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. pinholes.
- C. failure to cure.
- D. chalking.
正解：B
質問 # 32
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
正解：B
質問 # 33
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are expected to degrade over time.
- B. linings protect the contents and the container.
- C. linings are more durable than coatings.
- D. coatings are more durable than linings.
正解：B
質問 # 34
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by acid etching
- B. SP 1 followed by SP 2
- C. SP 1 followed by caustic etching
- D. SP 1 followed by SP 3
正解：B
質問 # 35
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
正解：A
質問 # 36
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Call your supervisor
- C. Refuse to take readings until an is in place
- D. Use a generally accepted industry standard and to take readings
正解：D
質問 # 37
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. coating type.
- B. time of the year (winter/summer).
- C. manufacturer of the equipment.
- D. type of dehumidification equipment (refrigerant or desiccant).
正解：A
質問 # 38
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. washed with clean potable water prior to Use.
- B. mixed with uncontaminated abrasive
- C. run through the air wash separator.
- D. disposed of properly.
正解：D
質問 # 39
......
更新されたNACE-CIP2-001試験練習テスト問題：https://www.jpntest.com/shiken/NACE-CIP2-001-mondaishu