[2024年06月]更新のJN0-351問題集完全版解答でJNCIS-ENT試験学習ガイド
試験問題と解答JN0-351学習ガイド
質問 # 33
What are two reasons for creating multiple areas in OSPF? (Choose two.)
- A. to increase the number of adjacencies in the backbone
- B. to reduce the convergence time
- C. to increase the size of the LSDB
- D. to reduce LSA flooding across the network
正解：B、D
解説：
Explanation
Option A is correct. Creating multiple areas in OSPF can help to reduce the convergence time . This is because changes in one area do not affect other areas, so fewer routers need to run the SPF algorithm in response to a change.
Option D is correct. Creating multiple areas in OSPF can help to reduce Link State Advertisement (LSA) flooding across the network. This is because LSAs are not flooded out of their area of origin.
質問 # 34
Which statement is correct about graceful Routing Engine switchover (GRES)?
- A. When combined with NSR, routing is preserved and the new master RE does not restart rpd.
- B. The PFE restarts and the kernel and interface information is lost.
- C. With no other high availability features enabled, routing is preserved and the new master RE does not restart rpd.
- D. GRES has a helper mode and a restarting mode.
正解：A
解説：
Explanation
The Graceful Routing Engine Switchover (GRES) feature in Junos OS enables a router with redundant Routing Engines to continue forwarding packets, even if one Routing Engine fails1. GRES preserves interface and kernel information, ensuring that traffic is not interrupted1. However, GRES does not preserve the control plane1.
To preserve routing during a switchover, GRES must be combined with either Graceful Restart protocol extensions or Nonstop Active Routing (NSR)1. When GRES is combined with NSR, nearly 75 percent of line rate worth of traffic per Packet Forwarding Engine remains uninterrupted during GRES1. Any updates to the primary Routing Engine are replicated to the backup Routing Engine as soon as they occur1.
Therefore, when GRES is combined with NSR, routing is preserved and the new master RE does not restart rpd1.
質問 # 35
Which two statements are correct about generated routes? (Choose two.)
- A. Generated routes cannot be redistributed into dynamic routing protocols.
- B. Generated routes require a contributing route.
- C. Generated routes appear in the routing table as static routes
- D. Generated routes show a next hop in the routing table.
正解：B、D
解説：
A is correct because generated routes require a contributing route. A contributing route is a route that matches the destination prefix of the generated route and has a valid next hop1. A generated route is only installed in the routing table if there is at least one contributing route available2. This ensures that the generated route is reachable and useful. If there is no contributing route, the generated route is not added to the routing table2.
B is correct because generated routes show a next hop in the routing table. A generated route inherits the next hop of its primary contributing route, which is the most preferred route among all the contributing routes2. The next hop of the generated route can be either an IP address or an interface name, depending on the type of the contributing route2. The next hop of the generated route can also be modified by a routing policy3.
質問 # 36
Which two statements about BGP facilitate the prevention of routing loops between two autonomous systems?
(Choose two.)
- A. EBGP routers will prepend their AS number when advertising routes to their neighbors
- B. EBGP routers will append their AS number when advertising routes to their neighbors.
- C. EBGP routers will only accept routes that contain their own AS number in the AS_PATH.
- D. EBGP routers will drop routes that contain their own AS number in the AS_PATH
正解：B、D
解説：
Explanation
BGP (Border Gateway Protocol) is a protocol designed to exchange routing and reachability information among autonomous systems (AS) on the internet1.
Option A is correct. When an EBGP router advertises routes to its neighbors, it appends its AS number to the AS_PATH attribute1. This is a key mechanism in BGP to prevent routing loops1.
Option C is correct. BGP has a built-in loop prevention mechanism whereby if a BGP router detects its own AS in the AS_PATH attribute, it will drop the prefix and will not continue to advertise it2. This helps to prevent routing loops2.
Option B is incorrect. EBGP routers do not accept routes that contain their own AS number in the AS_PATH2. Instead, they drop such routes as part of the loop prevention mechanism2.
Option D is incorrect. While it's true that EBGP routers append their AS number when advertising routes, they do not prepend their AS number1. The term "prepend" in BGP usually refers to a technique used to influence path selection by artificially lengthening the AS_PATH3.
質問 # 37
Which two statements correctly describe RSTP port roles? (Choose two.)
- A. The backup port is used as a backup for the root port.
- B. The designated port forwards data to the downstream network segment or device.
- C. The alternate port is a standby port for an edge port.
- D. The root port is responsible for forwarding data to the root bridge.
正解：B、D
解説：
Explanation
In Rapid Spanning Tree Protocol (RSTP), there are several port roles that determine the behavior of the port in the spanning tree1.
Option A suggests that the designated port forwards data to the downstream network segment or device. This is correct because the designated port is the port on a network segment that has the best path to the root bridge1. It's responsible for forwarding frames towards the root bridge and sending configuration messages into its segment1.
Option D suggests that the root port is responsible for forwarding data to the root bridge. This is also correct because the root port is always the link directly connected to the root bridge, or the shortest path to the root bridge1. It's used to forward traffic towards the root bridge1.
Therefore, options A and D are correct.
質問 # 38
You are asked to connect an IP phone and a user computer using the same interface on an EX Series switch.
The traffic from the computer does not use a VLAN tag, whereas the traffic from the IP phone uses a VLAN tag.
Which feature enables the interface to receive both types of traffic?
- A. voice VLAN
- B. MAC limiting
- C. native VLAN
- D. DHCP snooping
正解：A
解説：
Explanation
The feature that enables an interface on an EX Series switch to receive both untagged traffic (from the computer) and tagged traffic (from the IP phone) is the voice VLAN12.
The voice VLAN feature in EX-series switches enables access ports to accept both data (untagged) and voice (tagged) traffic and separate that traffic into different VLANs12. This allows the switch to differentiate between voice and data traffic, ensuring that voice traffic can be treated with a higher priority12. Therefore, option D is correct.
質問 # 39
Which statement about aggregate routes is correct?
- A. Aggregate routes can only be used for static routing but not for dynamic routing protocols.
- B. Aggregate routes are used for advertising summarized network prefixes.
- C. Aggregate routes are always preferred over more specific routes, even when the specific routes have a better path.
- D. Aggregate routes are automatically generated for all of the subnets in a routing table.
正解：B
解説：
Explanation
Aggregate routes are used for advertising summarized network prefixes12. They help minimize the number of routing tables in an IP network by consolidating selected multiple routes into a single route advertisement1. This approach is in contrast to non-aggregation routing, in which every routing table contains a unique entry for each route1.
Therefore, option D is correct. Options A, B, and C are not correct because:
Aggregate routes can be used with both static routing and dynamic routing protocols1.
Aggregate routes are not automatically generated for all of the subnets in a routing table. They need to be manually configured1.
Aggregate routes are not always preferred over more specific routes. The route selection process in Junos OS considers several factors, including route preference and metric, before determining the active route1.
質問 # 40
Exhibit
You have configured a GRE tunnel. To reduce the risk of dropping traffic, you have configured a keepalive OAM probe to monitor the state of the tunnel; however, traffic drops are still occurring.
Referring to the exhibit, what is the problem?
- A. The "event link-adjacency-loss" option must be set.
- B. For GRE tunnels, the OAM protocol requires that the BFD protocols also be used.
- C. LLDP needs to be removed from the gr-1/1/10.1 interface.
- D. The hold-time value must be two times the keepalive-time value
正解：D
解説：
Explanation
A keepalive OAM probe is a mechanism that can be used to monitor the state of a GRE tunnel and detect any failures in the tunnel path. A keepalive OAM probe consists of sending periodic packets from one end of the tunnel to the other and expecting a reply. If no reply is received within a specified time, the tunnel is considered down and the line protocol of the tunnel interface is changed to down1.
To configure a keepalive OAM probe for a GRE tunnel, you need to specify two parameters: the keepalive-time and the hold-time. The keepalive-time is the interval between each keepalive packet sent by the local router. The hold-time is the maximum time that the local router waits for a reply from the remote router before declaring the tunnel down2.
According to the Juniper Networks documentation, the hold-time value must be two times the keepalive-time value for a GRE tunnel2. This is because the hold-time value must account for both the round-trip time of the keepalive packet and the processing time of the remote router. If the hold-time value is too small, it may cause false positives and unnecessary tunnel flaps.
In the exhibit, the configuration shows that the keepalive-time is set to 10 seconds and the hold-time is set to
15 seconds for the gr-1/1/10.1 interface. This means that the local router will send a keepalive packet every 10 seconds and will wait for 15 seconds for a reply from the remote router. However, this hold-time value is not two times the keepalive-time value, which violates the recommended configuration. This may cause traffic drops if the remote router takes longer than 15 seconds to reply.
Therefore, option D is correct, because the hold-time value must be two times the keepalive-time value for a GRE tunnel. Option A is incorrect, because BFD is not required for GRE tunnels; BFD is another protocol that can be used to monitor tunnels, but it is not compatible with GRE keepalives3. Option B is incorrect, because the "event link-adjacency-loss" option is not related to GRE tunnels; it is an option that can be used to trigger an action when a link goes down4. Option C is incorrect, because LLDP does not need to be removed from the gr-1/1/10.1 interface; LLDP is a protocol that can be used to discover neighboring devices and their capabilities, but it does not interfere with GRE tunnels5.
References:
1: Configuring Keepalive Time and Hold time for a GRE Tunnel Interface 2: keepalive | Junos OS | Juniper Networks 3: Configuring Bidirectional Forwarding Detection 4: event link-adjacency-loss | Junos OS | Juniper Networks 5: Understanding Link Layer Discovery Protocol
質問 # 41
Which two statements are correct about tunnels? (Choose two.)
- A. IP-IP tunnels are stateful.
- B. Tunnels add additional overhead to packet size.
- C. Tunnel endpoints must have a valid route to the remote tunnel endpoint.
- D. BFD cannot be used to monitor tunnels.
正解：B、C
解説：
Explanation
A tunnel is a connection between two computer networks, in which data is sent from one network to another through an encrypted link. Tunnels are commonly used to secure data communications between two networks or to connect two networks that use different protocols.
Option B is correct, because tunnel endpoints must have a valid route to the remote tunnel endpoint. A tunnel endpoint is the device that initiates or terminates a tunnel connection. For a tunnel to be established, both endpoints must be able to reach each other over the underlying network. This means that they must have a valid route to the IP address of the remote endpoint1.
Option D is correct, because tunnels add additional overhead to packet size. Tunnels work by encapsulating packets: wrapping packets inside of other packets. This means that the original packet becomes the payload of the surrounding packet, and the surrounding packet has its own header and trailer. The header and trailer of the surrounding packet add extra bytes to the packet size, which is called overhead. Overhead can reduce the efficiency and performance of a network, as it consumes more bandwidth and processing power2.
Option A is incorrect, because BFD can be used to monitor tunnels. BFD is a protocol that can be used to quickly detect failures in the forwarding path between two adjacent routers or switches. BFD can be integrated with various routing protocols and link aggregation protocols to provide faster convergence and fault recovery.
BFD can also be used to monitor the connectivity of tunnels, such as GRE, IPsec, or MPLS.
Option C is incorrect, because IP-IP tunnels are stateless. IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels are stateless, which means that they do not keep track of the state or status of the tunnel connection. Stateless tunnels do not require any signaling or negotiation between the endpoints, but they also do not provide any error detection or recovery mechanisms.
References:
1: What is Tunneling? | Tunneling in Networking 2: What Is Tunnel In Networking, Its Types, And Its Benefits? : [Configuring Bidirectional Forwarding Detection] : [IP-IP Tunneling]
質問 # 42
Exhibit
You are receiving the BGP route shown in the exhibit from four different upstream ISPs.
Referring to the exhibit, which ISP will be selected as the active path?
- A. ISP 4
- B. ISP 2
- C. ISP1
- D. ISP 3
正解：A
解説：
Explanation
In BGP, the path selection process is based on a set of attributes1. The process starts by preferring the path with the highest weight, then the highest local preference, then the locally originated routes, and so on1. If all these attributes are the same, then it prefers the path with the shortest AS path1.
Referring to the exhibit, all four ISPs have the same weight, local preference, and origin1. However, ISP 4 has the shortest AS path1. Therefore, ISP 4 will be selected as the active path. So, option C is correct.
質問 # 43
You are attempting to configure the initial two aggregated Ethernet interfaces on a router but there are no aggregated Ethernet interfaces available.
In this scenario, which configuration will enable these interfaces on this router?
- A.
- B.
- C.
- D.
正解：B
解説：
Explanation
The correct answer to your question is
Option C shows the configuration of the statement, which defines the properties of the router chassis, such as the number of aggregated Ethernet interfaces, the number of FPCs, and the number of PICs1.
To enable aggregated Ethernet interfaces on a router, you need to specify the aggregated-devices statement under the chassis parameter to the desired number of interfaces2. For example, to enable two aggregated Ethernet interfaces, you can use the following configuration:
chassis { aggregated-devices { ethernet { device-count 2; } } }
Option C shows this configuration with the device-count set to 2, which will enable two aggregated Ethernet interfaces on the router. The other options do not show this configuration and will not enable any aggregated Ethernet interfaces on the router.
Therefore, option C is the correct answer to your question.
質問 # 44
What are two characteristics of RSTP alternate ports? (Choose two.)
- A. RSTP alternate ports provide an alternate lower cost path to the root bridge.
- B. RSTP alternate ports are active ports used to forward frames toward the root bridge.
- C. RSTP alternate ports provide an alternate higher cost path to the root bridge.
- D. RSTP alternate ports block traffic while receiving superior BPDUs from a neighboring switch.
正解：C、D
解説：
A is correct because RSTP alternate ports block traffic while receiving superior BPDUs from a neighboring switch. An alternate port is a backup port for a root port, which means it receives better BPDUs from another bridge than the current root port1. However, an alternate port does not forward any traffic, as it is in a discarding state2. It only listens to BPDUs and waits for the root port to fail. If the root port fails, the alternate port can immediately transition to a forwarding state and become the new root port1.
C is correct because RSTP alternate ports provide an alternate higher cost path to the root bridge. An alternate port is selected based on the same criteria as the root port, which are the lowest bridge ID, the lowest path cost, the lowest sender port ID, and the lowest receiver port ID3. However, an alternate port receives a higher cost BPDU than the root port, otherwise it would be the root port itself1. Therefore, an alternate port provides an alternate higher cost path to the root bridge than the root port.
質問 # 45
Exhibit
You are a network operator troubleshooting BGP connectivity.
Which two statements are correct about the output shown in the exhibit? (Choose two.)
- A. The routers are exchanging IPv4 routes.
- B. The R1 is configured for AS 65400.
- C. The BGP session is not established.
- D. Peer 10.32.1.2 is configured for AS 63645.
正解：B、C
解説：
Explanation
Option B suggests that the BGP session is not established. This is correct because in the output, the state of the BGP session is shown as "Idle". In BGP, an "Idle" state means that the BGP session is not currently established1.
Option C suggests that R1 is configured for AS 65400. This is also correct because in the output, it's shown that the local AS number is 654001. The local AS number represents the Autonomous System (AS) number of the router on which you're checking the BGP session1.
質問 # 46
Which statement is correct about IP-IP tunnels?
- A. There are 24 bytes of overhead with IP-IP encapsulation.
- B. IP-IP tunnels only support encapsulating non-IP traffic.
- C. IP-IP tunnels only support encapsulating IP traffic.
- D. The TTL in the inner packet is decremented during transit to the tunnel endpoint.
正解：C
解説：
Explanation
IP-IP tunnels are a type of tunnels that use IP as both the encapsulating and encapsulated protocol. IP-IP tunnels are simple and easy to configure, but they do not provide any security or authentication features. IP-IP tunnels only support encapsulating IP traffic, which means that the payload of the inner packet must be an IP packet. IP-IP tunnels cannot encapsulate non-IP traffic, such as Ethernet frames or MPLS labels1.
Option A is correct, because IP-IP tunnels only support encapsulating IP traffic. Option B is incorrect, because IP-IP tunnels only support encapsulating non-IP traffic. Option C is incorrect, because the TTL in the inner packet is not decremented during transit to the tunnel endpoint. The TTL in the outer packet is decremented by each router along the path, but the TTL in the inner packet is preserved until it reaches the tunnel endpoint2.
Option D is incorrect, because there are 20 bytes of overhead with IP-IP encapsulation. The overhead consists of the header of the outer packet, which has a fixed size of 20 bytes for IPv43.
References:
1: IP-IP Tunneling 2: What is tunneling? | Tunneling in networking 3: IPv4 - Header
質問 # 47
Which statement is correct about the storm control feature?
- A. The storm control feature is enabled in the factory-default configuration on EX Series switches.
- B. The storm control feature requires a special license on EX Series switches.
- C. The storm control configuration only applies to traffic being sent between the forwarding and control plane.
- D. The storm control feature is not supported on aggregate Ethernet interfaces.
正解：A
解説：
Option A is correct. The storm control feature is enabled in the factory-default configuration on EX Series switches12. On EX2200, EX3200, EX3300, EX4200, and EX6200 switches, the factory default configuration enables storm control for broadcast and unknown unicast traffic on all switch interfaces2. On EX4300 switches, the factory default configuration enables storm control on all Layer 2 switch interfaces1.
Option B is incorrect. The storm control feature does not require a special license on EX Series switches34.
Option C is incorrect. There's no information available that suggests the storm control feature is not supported on aggregate Ethernet interfaces.
Option D is incorrect. The storm control configuration applies to traffic at the ingress of an interface5, not just between the forwarding and control plane.
質問 # 48
You want to ensure traffic is routed through a GRE tunnel.
In this scenario, which two statements will satisfy this requirement? (Choose two.)
- A. BFD must be used on the stateless tunneling protocols.
- B. All intermediary devices must have a route to the tunnel endpoints.
- C. Keepalives must be used on stateless tunneling protocols.
- D. Tunnel endpoints must have a route that directs traffic into the tunnel.
正解：B、D
解説：
Explanation
Option A is correct. For traffic to be sent through a GRE tunnel, there must be a route that directs the traffic into the tunnel. This is typically accomplished through the use of a static route or a dynamic routing protocol.
Option B is correct. All intermediary devices must have a route to the tunnel endpoints34. In real-world scenarios, the tunnel endpoints for a tunnel going over the Internet must have globally reachable internet addresses. Otherwise, intermediate routers in the Internet cannot forward the tunneled packets.
質問 # 49
You are asked to create a new firewall filter to evaluate Layer 3 traffic that is being sent between VLANs. In this scenario, which two statements are correct? (Choose two.)
- A. You should create a family inet firewall filter with the appropriate match criteria and actions.
- B. You should apply the firewall filter to the appropriate IRB interface.
- C. You should apply the firewall filter to the appropriate VLAN.
- D. You should create a family Ethernet-switching firewall filter with the appropriate match criteria and actions.
正解：A、B
解説：
Explanation
A firewall filter is a configuration that defines the rules that determine whether to forward or discard packets at specific processing points in the packet flow. A firewall filter can also modify the attributes of the packets, such as priority, marking, or logging. A firewall filter can be applied to various interfaces, protocols, or routing instances on a Juniper device1.
A firewall filter has a family attribute, which specifies the type of traffic that the filter can evaluate. The family attribute can be one of the following: inet, inet6, mpls, vpls, iso, or ethernet-switching2. The family inet firewall filter is used to evaluate IPv4 traffic, which is the most common type of Layer 3 traffic on a network.
To create a family inet firewall filter, you need to specify the appropriate match criteria and actions for each term in the filter. The match criteria can include various fields in the IPv4 header, such as source address, destination address, protocol, port number, or DSCP value. The actions can include accept, discard, reject, count, log, policer, or next term3.
To apply a firewall filter to Layer 3 traffic that is being sent between VLANs, you need to apply the filter to the appropriate IRB interface. An IRB interface is an integrated routing and bridging interface that provides Layer 3 functionality for a VLAN on a Juniper device. An IRB interface has an IP address that acts as the default gateway for the hosts in the VLAN. An IRB interface can also participate in routing protocols and forward packets to other VLANs or networks4.
Therefore, option C is correct, because you should create a family inet firewall filter with the appropriate match criteria and actions. Option D is correct, because you should apply the firewall filter to the appropriate IRB interface.
Option A is incorrect, because you should not create a family ethernet-switching firewall filter with the appropriate match criteria and actions. A family ethernet-switching firewall filter is used to evaluate Layer 2 traffic on a Juniper device. A family ethernet-switching firewall filter can only match on MAC addresses or VLAN IDs, not on IP addresses or protocols5.
Option B is incorrect, because you should not apply the firewall filter to the appropriate VLAN. A VLAN is a logical grouping of hosts that share the same broadcast domain on a Layer 2 network. A VLAN does not have an IP address or routing capability. A firewall filter cannot be applied directly to a VLAN; it must be applied to an interface that belongs to or connects to the VLAN6.
References:
1: Firewall Filters Overview 2: Configuring Firewall Filters 3: Configuring Firewall Filter Match Conditions and Actions 4: Understanding Integrated Routing and Bridging Interfaces 5: Configuring Ethernet-Switching Firewall Filters 6: Understanding VLANs
質問 # 50
You are an operator for a network running 1S-IS. Two routers are failing to form an adjacency. What are two reasons for this problem? (Choose two.)
- A. There are mismatched router IDs on the L2 routers.
- B. There is no configured ISO address on any IS-IS interface.
- C. The family iso configuration is missing from the adjacency interface.
- D. There is a mismatched area ID between the L2 routers.
正解：B、C
解説：
Explanation
The two reasons for the failure to form an adjacency in a network running IS-IS could be:
B: There is no configured ISO address on any IS-IS interface. IS-IS requires each router interface to have an ISO address configured. Without this address, the routers cannot form an adjacency1.
D: The family iso configuration is missing from the adjacency interface. The 'family iso' configuration is essential for IS-IS to function correctly. If this configuration is missing from the adjacency interface, it could prevent the formation of an adjacency1.
These explanations are based on the Enterprise Routing and Switching Specialist (JNCIS-ENT) documents and learning resources available at Juniper Networks23.
質問 # 51
Exhibit
Which command displays the output shown in the exhibit?
- A. show route forwarding-table
- B. show route forwarding-table family ethernet-switching
- C. show ethernet-switching table
- D. show ethernet-switching table extensive
正解：C
解説：
The output shown in the exhibit is a brief display of the Ethernet switching table, which shows the learned Layer 2 MAC addresses for each VLAN and interface1.
The command show ethernet-switching table displays the Ethernet switching table with brief information, such as the destination MAC address, the VLAN name, the forwarding state, and the interface name1.
The command show route forwarding-table displays the routing table information for each protocol family, such as inet, inet6, mpls, iso, and so on2. It does not show the Ethernet switching table or the MAC addresses.
The command show ethernet-switching table extensive displays the Ethernet switching table with extensive information, such as the destination MAC address, the VLAN name, the forwarding state, the interface name, the VLAN index, and the tag type1. It shows more details than the brief output shown in the exhibit.
The command show route forwarding-table family ethernet-switching displays the routing table information for the ethernet-switching protocol family, whichshows the destination MAC address, the next-hop MAC address, and the interface name3. It does not show the VLAN name or the forwarding state.
質問 # 52
You are concerned about spoofed MAC addresses on your LAN.
Which two Layer 2 security features should you enable to minimize this concern? (Choose two.)
- A. IP source guard
- B. DHCP snooping
- C. static ARP
- D. dynamic ARP inspection
正解：B、D
解説：
A is correct because dynamic ARP inspection (DAI) is a Layer 2 security feature that prevents ARP spoofing attacks. ARP spoofing is a technique that allows an attacker to send fake ARP messages to associate a spoofed MAC address with a legitimate IP address. This can result in traffic redirection, man-in-the-middle attacks, or denial-of-service attacks. DAI validates ARP packets by checking the source MAC address and IP address against a trusted database, which is usually built by DHCP snooping1. DAI discards any ARP packets that do not match the database or have invalid formats1.
C is correct because DHCP snooping is a Layer 2 security feature that prevents DHCP spoofing attacks.
DHCP spoofing is a technique that allows an attacker to act as a rogue DHCP server and offer fake IP addresses and other network parameters to unsuspecting clients. This can result in traffic redirection, man-in-the-middle attacks, or denial-of-service attacks. DHCP snooping filters DHCP messages by classifying switch ports as trusted or untrusted. Trusted ports are allowed to send and receive any DHCP messages, while untrusted ports are allowed to send only DHCP requests and receive only valid DHCP replies from trusted ports2. DHCP snooping also builds a database of MAC addresses, IP addresses, lease times, and binding types for each client2.
質問 # 53
......
Juniper JN0-351 認定試験の出題範囲：
| トピック | 出題範囲 |
|---|---|
| トピック 1 |
|
| トピック 2 |
|
| トピック 3 |
|
| トピック 4 |
|
| トピック 5 |
|
| トピック 6 |
|
| トピック 7 |
|
| トピック 8 |
|
Enterprise Routing and Switching, Specialist (JNCIS-ENT)無料で更新される100%試験高合格率保証：https://www.jpntest.com/shiken/JN0-351-mondaishu
リアル試験問題と解答でJuniper JN0-351問題集はここにある：https://drive.google.com/open?id=1uEXmEgFc1_Y34X0h5YtJHEDrPo_C_kFU