JN0-351試験問題でリアルに更新された問題PDF
合格させる無料保証付きクイズ2024年最新の実際に出ると確認されたJuniper
質問 # 26
Exhibit.
Why is this OSPF adjacency remaining in this state?
- A. An area ID mismatch exists between the OSPF neighbors
- B. A subnet mask mismatch exists between the OSPF neighbors.
- C. A hello interval mismatch exists between the OSPF neighbors.
- D. An MTU mismatch exists between the OSPF neighbors.
正解：D
解説：
The exhibit shows the output of the command , which displays information about the OSPF neighbors on a router1.
The output shows that the OSPF neighbor with the address 172.26.1.1 and the interface ge-0/0/3.0 is in the Exstart state1.
The Exstart state is the fourth state in the OSPF neighbor formation process, after Down, Init, and
2-Way states2. In this state, the OSPF neighbors establish a master-slave relationship and exchange database description (DBD) packets, which contain summaries of their link-state databases2.
The most common reason for OSPF neighbors to be stuck in the Exstart state is an MTU mismatch between the interfaces3. MTU stands for maximum transmission unit, which is the largest size of a packet that can be transmitted on a network segment4. If the MTU values of two OSPF neighbors are different, theymay not be able to exchange DBD packets successfully, as some packets may be dropped or fragmented due to their size exceeding the MTU limit3.
To solve this problem, you need to ensure that the MTU values of both OSPF neighbors are the same or compatible. You can use the command show interfaces to display the MTU value of an interface5. You can also use the command ping with the do-not-fragment option to test the MTU size between two routers. You can change the MTU value of an interface by using the command set interfaces interface-name mtu mtu-value in configuration mode5.
質問 # 27
Which two events cause a router to advertise a connected network to OSPF neighbors? (Choose two.)
- A. When an interface has the OSPF passive option enabled.
- B. When an OSPF adjacency is established.
- C. When a static route to the 224.0.0.6 address is created.
- D. When a static route to the 224.0.0.5 address is created.
正解：B、D
解説：
A is correct because when an OSPF adjacency is established, a router will advertise a connected network to OSPF neighbors. An OSPF adjacency is a logical relationship between two routers that agree to exchange routing information using the OSPF protocol1. To establish an OSPF adjacency, the routers must be in the same area, have compatible parameters, and exchange hello packets1. Once an OSPF adjacency is formed, the routers will exchange database description (DBD) packets, which contain summaries of their link-state databases (LSDBs)1. The LSDBs include information about the connected networks and their costs2. Therefore, when an OSPF adjacency is established, a router will advertise a connected network to OSPF neighbors through DBD packets.
D is correct because when a static route to the 224.0.0.5 address is created, a router will advertise a connected network to OSPF neighbors. The 224.0.0.5 address is the multicast address for all OSPF routers3. A static route to this address can be used to send OSPF hello packets to all OSPF neighbors on a network segment3. This can be useful when the network segment does not support multicast or when the router does not have an IP address on the segment3. When a static route to the 224.0.0.5 address is created, the router will send hello packets to this address and establish OSPF adjacencies with other routers on the segment3. As explained above, once an OSPF adjacency is formed, the router will advertise a connected network to OSPF neighbors through DBD packets.
質問 # 28
Which three protocols support BFD? (Choose three.)
- A. RSTP
- B. BGP
- C. LACP
- D. FTP
- E. OSPF
正解：B、C、E
解説：
Explanation
BFD is a protocol that can be used to quickly detect failures in the forwarding path between two adjacent routers or switches. BFD can be integrated with various routing protocols and link aggregation protocols to provide faster convergence and fault recovery.
According to the Juniper Networks documentation, the following protocols support BFD on Junos OS devices1:
BGP: BFD can be used to monitor the connectivity between BGP peers and trigger a session reset if a failure is detected. BFD can be configured for both internal and external BGP sessions, as well as for IPv4 and IPv6 address families2.
OSPF: BFD can be used to monitor the connectivity between OSPF neighbors and trigger a state change if a failure is detected. BFD can be configured for both OSPFv2 and OSPFv3 protocols, as well as for point-to-point and broadcast network types3.
LACP: BFD can be used to monitor the connectivity between LACP members and trigger a link state change if a failure is detected. BFD can be configured for both active and passive LACP modes, as well as for static and dynamic LAGs4.
Other protocols that support BFD on Junos OS devices are:
IS-IS: BFD can be used to monitor the connectivity between IS-IS neighbors and trigger a state change if a failure is detected. BFD can be configured for both level 1 and level 2 IS-IS adjacencies, as well as for point-to-point and broadcast network types.
RIP: BFD can be used to monitor the connectivity between RIP neighbors and trigger a route update if a failure is detected. BFD can be configured for both RIP version 1 and version 2 protocols, as well as for IPv4 and IPv6 address families.
VRRP: BFD can be used to monitor the connectivity between VRRP routers and trigger a priority change if a failure is detected. BFD can be configured for both VRRP version 2 and version 3 protocols, as well as for IPv4 and IPv6 address families.
The protocols that do not support BFD on Junos OS devices are:
RSTP: RSTP is a spanning tree protocol that provides loop prevention and rapid convergence in layer 2 networks. RSTP does not use BFD to detect link failures, but relies on its own hello mechanism that sends BPDU packets every 2 seconds by default.
FTP: FTP is an application layer protocol that is used to transfer files between hosts over a TCP connection. FTP does not use BFD to detect connection failures, but relies on TCP's own retransmission and timeout mechanisms.
References:
1: [Configuring Bidirectional Forwarding Detection] 2: [Configuring Bidirectional Forwarding Detection for BGP] 3: [Configuring Bidirectional Forwarding Detection for OSPF] 4: [Configuring Bidirectional Forwarding Detection for Link Aggregation Control Protocol] : [Configuring Bidirectional Forwarding Detection for IS-IS] : [Configuring Bidirectional Forwarding Detection for RIP] : [Configuring Bidirectional Forwarding Detection for VRRP] : [Understanding Rapid Spanning Tree Protocol] : [Understanding FTP]
質問 # 29
Exhibit
You are troubleshooting an issue where traffic to 192.168.10.0/24 is being sent to R1 instead of your desired path through R2.
Referring to the exhibit, what is the reason for the problem?
- A. R1's route is the best path due to a higher local preference
- B. R1's route is the best path due to the shorter AS path.
- C. R2's route is not the best path due to loop prevention.
- D. R2's route is not the best path due to a lower origin code.
正解：A
解説：
The exhibit shows the output of the command show ip bgp, which displays information about the BGP routes in the routing table1. The output shows two routes for the destination 192.168.10.0/24, one from R1 and one from R2.
The route from R1 has a local preference of 200, while the route from R2 has a local preference of
100. Local preference is a BGP attribute that indicates the degree of preference for a route within an autonomous system (AS)2. A higher local preference means a more preferred route2.
BGP uses a best path selection algorithm to choose the best route for each destination among multiple paths. The algorithm compares different attributes of the routes in a specific order of precedence3. The first attribute that is compared is weight, which is a Cisco-specific attribute that is local to the router3. If the weight is equal or not set, the next attribute that is compared is local preference3.
In this case, both routes have the same weight of 0, which means that they are learned from external BGP (eBGP) peers3. Therefore, the next attribute that is compared is local preference. Since R1's route has a higher local preference than R2's route, it is chosen as the best path and installed in the routing table3. The other attributes, such as origin code and AS path, are not considered in this case.
質問 # 30
Which statement about aggregate routes is correct?
- A. Aggregate routes are always preferred over more specific routes, even when the specific routes have a better path.
- B. Aggregate routes can only be used for static routing but not for dynamic routing protocols.
- C. Aggregate routes are used for advertising summarized network prefixes.
- D. Aggregate routes are automatically generated for all of the subnets in a routing table.
正解：C
解説：
Explanation
Aggregate routes are used for advertising summarized network prefixes12. They help minimize the number of routing tables in an IP network by consolidating selected multiple routes into a single route advertisement1. This approach is in contrast to non-aggregation routing, in which every routing table contains a unique entry for each route1.
Therefore, option D is correct. Options A, B, and C are not correct because:
Aggregate routes can be used with both static routing and dynamic routing protocols1.
Aggregate routes are not automatically generated for all of the subnets in a routing table. They need to be manually configured1.
Aggregate routes are not always preferred over more specific routes. The route selection process in Junos OS considers several factors, including route preference and metric, before determining the active route1.
質問 # 31
You need to configure a LAG between your switches. In this scenario, which two statements are correct?
(Choose two.)
- A. Member links are not required to be contiguous ports.
- B. Member links are required to be contiguous ports.
- C. Duplex and speed settings are not required to match on both participating devices.
- D. Duplex and speed settings are required to match on both participating devices.
正解：A、D
解説：
B is correct because duplex and speed settings are required to match on both participating devices. According to the Juniper Networks documentation1, all the interfaces in a LAG must have the same speed and be in full-duplex mode. This ensures that the LAG can operate as a single logical link without any performance or compatibility issues.
C is correct because member links are not required to be contiguous ports. According to the Juniper Networks documentation2, you can group any Ethernet interfaces on a switch into a LAG, regardless of their physical location or slot number. This provides flexibility and scalability for configuring LAGs on switches.
質問 # 32
What is the maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation?
- A. 1476 bytes
- B. 1480 bytes
- C. 1496 bytes
- D. 1500 bytes
正解：A
解説：
Explanation
The maximum allowable MTU size for a default GRE tunnel without IPv4 traffic fragmentation is 1476 bytes1. This is because GRE packets are formed by the addition of the original packets and the required GRE headers1. These headers are 24-bytes in length and since these headers are added to the original frame, depending on the original size of the packet we may run into IP MTU problems1. The most common IP MTU is 1500-bytes in length (Ethernet)1. When the tunnel is created, it deducts the 24-bytes it needs to encapsulate the passenger protocols and that is the IP MTU it will use1. For example, if we are forming a tunnel over FastEthernet (IP MTU 1500)the IOS calculates the IP MTU on the tunnel as: 1500-bytes from Ethernet -
24-bytes for the GRE encapsulation = 1476-Bytes1.
質問 # 33
Exhibit.
You are using OSPF to advertise the subnets that are used by the Denver and Dallas offices. The routers that are directly connected to the Dallas and Denver subnets are not advertising the connected subnets.
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. Configure and apply a routing policy that redistributes the connected Dallas and Denver subnets.
- B. Create static routes on the switches using the local vMX router's loopback interface for the next hop.
- C. Configure and apply a routing policy that redistributes the Dallas and Denver subnets using Type 5 LSAs.
- D. Enable the passive option on the OSPF interfaces that are connected to the Dallas and Denver subnets.
正解：A、D
解説：
Explanation
The routers that are directly connected to the Dallas and Denver subnets are not advertising the connected subnets. This can be resolved by redistributing the connected subnets into OSPF1.
Option C suggests to configure and apply a routing policy that redistributes the connected Dallas and Denver subnets. This is correct because redistribution allows routes from one routing protocol to be communicated to another, and in this case, it allows the connected subnets to be advertised through OSPF1.
Option D suggests enabling the passive option on the OSPF interfaces that are connected to the Dallas and Denver subnets. This is also correct because in OSPF, a passive interface is an interface that belongs to the OSPF router, but does not send OSPF Hello packets1. It's typically used on an interface that you don't want to use for OSPF adjacencies, but you still want to advertise its IP address1. Therefore, enabling passive interface can help in advertising the Dallas and Denver subnets.
質問 # 34
Exhibit.
What is the management IP address of the device shown in the exhibit?
- A. 128.0.0.1
- B. 172.23.12.100
- C. 172.23.11.10
- D. 10.210.20.233
正解：B
解説：
Explanation
The management IP address of a device is the IP address that is used to access the device for configuration and monitoring purposes. It is usually assigned to a dedicatedmanagement interface that is separate from the data interfaces. The management interface can be accessed via SSH, Telnet, HTTP, or other protocols.
In the exhibit, the list of interfaces and their statuses shows that the management interface isme0. This interface has an admin status ofup, a protocol status ofinet, a local address of172.23.12.100/24, and a remote address ofunspecified. This means that the me0 interface is active, has an IPv4 address assigned, and is not connected to another device.
Therefore, the management IP address of the device shown in the exhibit is172.23.12.100.
References:
[Management Interfaces Overview] : [Displaying Interface Status Information]
質問 # 35
Exhibit
Referring to the exhibit, which two configuration changes must you apply for packets to reach from R1 to R3 using IS-IS? (Choose two.)
- A. On R1, disable Level 2 on the ge-0/0/1 interface.
- B. On R3 enable Level 1 on the ge-0/0/4 interface
- C. On R1, enable Level 1 on the ge-0/0/1 interface.
- D. On R3 disable Level 2 on the ge-0/0/4 interface.
正解：B、C
解説：
Explanation
A: On R1, enable Level 1 on the ge-0/0/1 interface. In IS-IS, both levels (Level 1 and Level 2) are enabled by default when you enable IS-IS on an interface1. Level 1 systems route within an area2. If the destination is outside an area, Level 1 systems route toward a Level 2 system2. Therefore, enabling Level 1 on the ge-0/0/1 interface on R1 would allow packets to reach from R1 to R3.
D: On R3 enable Level 1 on the ge-0/0/4 interface Similarly, enabling Level 1 on the ge-0/0/4 interface on R3 would allow packets to reach from R1 to R3.
These explanations are based on the IS-IS configuration documents and learning resources available at Juniper Networks1 and Cisco34.
質問 # 36
Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)
- A. Redundant trunk groups use spanning tree to provide loop-free redundant uplinks.
- B. Layer 2 control traffic is permitted on the secondary link.
- C. If the active link fails, then the secondary link automatically takes over.
- D. Redundant trunk groups load balance traffic across two designated uplink interfaces.
正解：B、C
解説：
C is correct because Layer 2 control traffic is permitted on the secondary link of a redundant trunk group (RTG) on EX Series switches. Layer 2 control traffic includes protocols such as LLDP, LACP, and STP, which are used to exchange information and coordinate actions between switches1. According to the Juniper Networks documentation2, Layer 2 control traffic is allowed to pass through both the active and the secondary links of an RTG, but data traffic is only forwarded through the active link. This allows the switches to maintain their Layer 2 adjacencies and monitor the link status on both links.
D is correct because if the active link fails, then the secondary link automatically takes over in an RTG on EX Series switches. An RTG consists of two trunk links: an active or primary link, and a secondary or backup link2. The active link is used to forward data traffic, while the secondary link is in standby mode. If the active link fails or becomes unavailable, the secondary link immediately transitions to a forwarding state and takes over the data traffic without waiting for normal STP convergence2. This provides fast recovery and redundancy for the network.
質問 # 37
You have two OSPF routers forming an adjacency. R1 has a priority of 32 and a router ID of 192.168.1.2. R2 has a priority of 64 and a router ID of 192.168.1.1. The routers were started at the same time and all other OSPF settings are the default settings.
Which statement is correct in this scenario?
- A. Router IDs must match for an adjacency to form.
- B. R2 will be the BDR.
- C. R1 will be the BDR.
- D. At least three routers are required for a DR/BDR election
正解：C
解説：
Explanation
In OSPF, the Designated Router (DR) and Backup Designated Router (BDR) are elected based on the priority of the routers1. The router with the highest priority becomes the DR, and the router with the second highest priority becomes the BDR1. If there is a tie in priority, then the router with the highest Router ID is chosen1.
In this scenario, R2 has a higher priority (64) than R1 (32), so R2 will become the DR1. Since R1 has the second highest priority, it will become the BDR1. Therefore, option D is correct.
質問 # 38
Which two types of tunnels are able to be created on all Junos devices? (Choose two.)
- A. GRE
- B. STP
- C. IP-IP
- D. IPsec
正解：A、D
解説：
Explanation
Junos devices support various types of tunnels for different purposes12.
Option B is correct. Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network1. Junos devices support GRE tunnels1.
Option D is correct. IPsec (Internet Protocol Security) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session1. Junos devices support IPsec tunnels1.
Option A is incorrect. Spanning Tree Protocol (STP) is not a type of tunnel. It's a network protocol designed to prevent loops in a bridged Ethernet local area network2.
Option C is incorrect. While Junos devices do support IP-IP (also known as IP tunneling), it's not supported on all Junos devices1.
質問 # 39
You are receiving multiple BGP routes from an upstream neighbor and only want to advertise a single summarized prefix to your internal OSPF neighbors. This route should only be advertised when you are receiving these BGP routes from this neighbor.
In this scenario, which type of route should you create?
- A. static route using the resolve feature
- B. static route using qualified next hops
- C. aggregate route
- D. generate route
正解：C
解説：
Explanation
In this scenario, you should create an 1. Aggregate routes are used for advertising summarized network prefixes1. They help minimize the number of routing tables in an IP network by consolidating selected multiple routes into a single route advertisement1. This approach is in contrast to non-aggregation routing, in which every routing table contains a unique entry for each route1.
Therefore, option A is correct. Options B, C, and D are not correct because:
Static route using the resolve feature: This type of route uses the resolve feature to install a static route in the routing table only if a specific condition is met1. However, it does not provide the capability to summarize multiple routes into a single prefix.
Generate route: This type of route generates a route that is always present in the routing table and can be used to summarize routes. However, it does not have the capability to only advertise the route when specific BGP routes are being received from a neighbor1.
Static route using qualified next hops: This type of route allows for the specification of multiple next-hop addresses for a static route1. However, it does not provide the capability to summarize multiple routes into a single prefix.
質問 # 40
Exhibit.
Which router will become the OSPF BDR if all routers are powered on at the same time?
- A. R1
- B. R2
- C. R4
- D. R3
正解：C
解説：
Explanation
OSPF DR/BDR election is a process that occurs on multi-access data links. It is intended to select two OSPF nodes: one to be acting as the Designated Router (DR), and another to be acting as the Backup Designated Router (BDR).The DR and BDR are responsible for generating network LSAs for the multi-access network and synchronizing the LSDB with other routers on the same network1.
The DR/BDR election is based on two criteria: the OSPF priority and the router ID. The OSPF priority is a value between 0 and 255 that can be configured on each interface participating in OSPF. The default priority is
1. A priority of 0 means that the router will not participate in the election and will never become a DR or BDR. The router with the highest priority will become the DR, and the router with the second highest priority will become the BDR. If there is a tie in priority, then the router ID is used as a tie-breaker. The router ID is a
32-bit number that uniquely identifies each router in an OSPF domain.It can be manually configured or automatically derived from the highest IP address on a loopback interface or any active interface2.
In this scenario, all routers have the same priority of 1, so the router ID will determine the outcome of the election. The router IDs are shown in the exhibit as RID values. The highest RID belongs to R4 (10.10.10.4), so R4 will become the DR. The second highest RID belongs to R3 (10.10.10.3), so R3 will become the BDR.
References:
1:OSPF DR/BDR Election: Process, Configuration, and Tuning2:OSPF Designated Router (DR) and Backup Designated Router (BDR)
質問 # 41
What is the default keepalive time for BGP?
- A. 90 seconds
- B. 30 seconds
- C. 10 seconds
- D. 60 seconds
正解：D
解説：
Explanation
The default keepalive time for BGP is 60 seconds1. The keepalive time is the interval at which BGP sends keepalive messages to maintain the connection with its peer1. If the keepalive message is not received within the hold time, the connection is considered lost1. By default, the hold time is three times the keepalive time, which is 180 seconds1.
質問 # 42
After receiving a BGP route, which two conditions are verified by the receiving router to ensure that the received route is valid? (Choose two)
- A. The local preference is greater than 0.
- B. The loops do not exist.
- C. The AS-path length is greater than 0.
- D. The next hop is reachable.
正解：B、D
解説：
B is correct because the loops do not exist is one of the conditions that are verified by the receiving router to ensure that the received BGP route is valid. A loop in BGP means that a route has been advertised by the same AS more than once, which can cause routing instability and inefficiency1. To prevent loops, BGP uses the AS-path attribute, which lists the AS numbers that a route has traversed from the origin to the destination2. The receiving router checks the AS-path attribute of the received route and discards it if it finds its own AS number in the list2. This way, BGP avoids accepting routes that contain loops.
C is correct because the next hop is reachable is one of the conditions that are verified by the receiving router to ensure that the received BGP route is valid. The next hop is the IP address of the next router that is used to forward packets to the destination network3. The receiving router checks the next hop attribute of the received route and verifies that it has a valid route to reach it3. If the next hop is not reachable, the received route is not usable and is rejected by the receiving router3. This way, BGP ensures that only feasible routes are accepted.
質問 # 43
You are asked to connect an IP phone and a user computer using the same interface on an EX Series switch.
The traffic from the computer does not use a VLAN tag, whereas the traffic from the IP phone uses a VLAN tag.
Which feature enables the interface to receive both types of traffic?
- A. MAC limiting
- B. native VLAN
- C. voice VLAN
- D. DHCP snooping
正解：C
解説：
Explanation
The feature that enables an interface on an EX Series switch to receive both untagged traffic (from the computer) and tagged traffic (from the IP phone) is the voice VLAN12.
The voice VLAN feature in EX-series switches enables access ports to accept both data (untagged) and voice (tagged) traffic and separate that traffic into different VLANs12. This allows the switch to differentiate between voice and data traffic, ensuring that voice traffic can be treated with a higher priority12. Therefore, option D is correct.
質問 # 44
What is the default MAC age-out timer on an EX Series switch?
- A. 30 seconds
- B. 30 minutes
- C. 300 minutes
- D. 300 seconds
正解：D
解説：
Explanation
The default MAC age-out timer on an EX Series switch is 300 seconds12. The MAC age-out timer is the maximum time that an entry can remain in the MAC table before it "ages out," or is removed31. This configuration can influence efficiency of network resource use by affecting the amount of traffic that is flooded to all interfaces1. When traffic is received for MAC addresses no longer in the Ethernet routing table, the router floods the traffic to all interfaces1.
質問 # 45
Which two statements about BGP facilitate the prevention of routing loops between two autonomous systems?
(Choose two.)
- A. EBGP routers will drop routes that contain their own AS number in the AS_PATH
- B. EBGP routers will prepend their AS number when advertising routes to their neighbors
- C. EBGP routers will only accept routes that contain their own AS number in the AS_PATH.
- D. EBGP routers will append their AS number when advertising routes to their neighbors.
正解：A、D
解説：
Explanation
BGP (Border Gateway Protocol) is a protocol designed to exchange routing and reachability information among autonomous systems (AS) on the internet1.
Option A is correct. When an EBGP router advertises routes to its neighbors, it appends its AS number to the AS_PATH attribute1. This is a key mechanism in BGP to prevent routing loops1.
Option C is correct. BGP has a built-in loop prevention mechanism whereby if a BGP router detects its own AS in the AS_PATH attribute, it will drop the prefix and will not continue to advertise it2. This helps to prevent routing loops2.
Option B is incorrect. EBGP routers do not accept routes that contain their own AS number in the AS_PATH2. Instead, they drop such routes as part of the loop prevention mechanism2.
Option D is incorrect. While it's true that EBGP routers append their AS number when advertising routes, they do not prepend their AS number1. The term "prepend" in BGP usually refers to a technique used to influence path selection by artificially lengthening the AS_PATH3.
質問 # 46
You want to use filter-based forwarding (FBF) on your Internet peering router to load-balance traffic to two directly connected ISPs based on the source address.
Which two statements are correct in this scenario? (Choose two.)
- A. FBF uses the forwarding routing instance type.
- B. FBF uses the no-forwarding routing instance type.
- C. RIB groups are used to hide routes in the inet. 0 routing table.
- D. RIB groups are used to copy routes from the inet. o routing table.
正解：A、D
解説：
Option B is correct. Filter-based forwarding (FBF), also known as Policy Based Routing (PBR), uses the forwarding routing instance type12.
Option C is correct. Routing Information Base (RIB) groups are used to copy routes from one routing table to another34. In the context of FBF, RIB groups can be used to copy routes from the inet.0 routing table34.
Option A is incorrect. FBF does not use the no-forwarding routing instance type15.
Option D is incorrect. RIB groups are not used to hide routes in the inet.0 routing table34. They are used to share or copy routes between different routing tables34.
質問 # 47
What is a purpose of using a spanning tree protocol?
- A. to look up MAC addresses
- B. to route IP packets
- C. to eliminate broadcast storms
- D. to tunnel Ethernet frames
正解：C
解説：
A broadcast storm is a network condition where a large number of broadcast packets are sent and received by multiple devices, causing congestion and performance degradation1. A broadcast storm can occur when there are loops in the network topology, meaning that there are multiple paths between two devices2.
A spanning tree protocol is a network protocol that prevents loops from being formed when switches or bridges are interconnected via multiple paths. It does this by creating a logical tree structure that spans all the devices in the network, and disabling or blocking the links that are not part of the tree, leaving a single active path between any two devices3.
By eliminating loops, a spanning tree protocol also eliminates broadcast storms, as broadcast packets will not be forwarded endlessly along the looped paths. Instead, broadcast packets will be sent only along the tree structure, reaching each device once and avoiding congestion3.
質問 # 48
......
トップクラスのJN0-351練習試験問題：https://www.jpntest.com/shiken/JN0-351-mondaishu
無料JNCIS-ENT JN0-351究極の学習ガイド：https://drive.google.com/open?id=1Egiwd3-MlF-i4nKy3HjuUqgTjlStu4To