最新の2023年最新の実際に出ると確認されたNACE-CIP1-001問題集で100%無料NACE-CIP1-001試験問題集
無料提供中で2023年最新のに更新されたNACE NACE-CIP1-001試験問題と解答
NACE認定コーティングインスペクターレベル1になることは、腐食防止プロセスにおける知識と技能を検証することで、プロフェッショナルのキャリアアップを促進することができます。この認定は、建設業界の多様な職種にも適格となることがあります。この認定は、コーティングおよびライニング産業でキャリアを向上させたいプロフェッショナルにとっての機会を開くことができます。
質問 # 45
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 45 Gauge readings resulting in 15 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
正解：D
質問 # 46
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades 1-4
- B. Rust Grades A-D
- C. Surface Condition H
- D. Surface Conditions E-G
正解：B
質問 # 47
If a Thermoset coating is heated it will:
- A. Soften when heated and return to its original hardness when cooled
- B. Harden and return to its original hardness when cooled
- C. Soften when heated and retain its softness when cooled
- D. Harden and retain its hardness when cooled
正解：D
質問 # 48
What is used to determine compressed air cleanliness?
- A. Needle pressure gauge
- B. Profilometer
- C. Psychrometer
- D. Blotter test
正解：B
質問 # 49
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Surface Temperature
- C. Low Relative Humidity
- D. High Relative Humidity
正解：C
質問 # 50
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Carefully review the document and do the best you can
- C. Hire a third patty to assist you in understanding the document
- D. Advise the owners' representative of your lack of knowledge in this area
正解：B
質問 # 51
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Ensure the instrument is within calibration parameters
- C. Be trained on how to use the instrument
- D. Read the manufactures' instructions
正解：A
質問 # 52
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. cracking.
- B. blistering.
- C. checking.
- D. alligatoring.
正解：C
質問 # 53
Dew point is the temperature at which
- A. water freezes.
- B. humidity decreases
- C. the air is saturated.
- D. condensation occurs.
正解：D
質問 # 54
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection and Non-destructive testing
- B. All types of inspection
- C. Visual inspection only
- D. Visual inspection, Non-Destructive and Destructive testing
正解：A
質問 # 55
If inspectors identify issues of non-conformance during an inspection, they should
- A. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
正解：A
質問 # 56
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. what materials were used.
- B. how the item was coated.
- C. what items were coated.
- D. when the coating will be reapplied.
正解：B
質問 # 57
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 58
Checking is
- A. an exposed area of the substrate or previous coat material, caused by poor application technique.
- B. a fine crack in the surface of a coating that rarely reaches the substrate
- C. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- D. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
正解：B
質問 # 59
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 4
- C. Level 1
- D. Level 2
正解：A
質問 # 60
According to SSPC PA 2 a Spot Measurement is:
- A. The overall average of all readings
- B. The average of all spot measurements in a given area
- C. The average of gauge readings taken in a 4cm (1.5 inch) circle
- D. A single gauge reading
正解：C
質問 # 61
......
NACE-CIP1-001問題集PDFとテストエンジン試験問題：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu