[2024年03月18日]NACE-CIP1-001問題集PDFとテストエンジン 試験問題
検証済みのNACE-CIP1-001テスト問題集と解答で正確な100問題解答あります
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、耐久性、密着力、総合品質に対する塗料の検査に関与する個人の知識とスキルを評価するために設計されています。この認定は、世界的に認知されており、National Association of Corrosion Engineers（NACE）Internationalによって提供されています。これは、個人がコーティング検査の分野での熟練度を証明し、就職市場で競争力を持つことができる基本的な認定です。
NACE-CIP1-001認定を取得することは、腐食防止分野における候補者のコミットメントと高品質なコーティング検査を実施する能力を示すことになります。これにより、求職機会の増加、高い収入、業界内でのより大きな尊敬を得ることができます。
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、コーティング業界または関連分野で働く個人にとって貴重なプログラムです。この認定は、認定コーティング検査官になるために必要な知識とスキルを個人に提供し、キャリアの進歩と雇用機会の増加につながる可能性があります。厳密なテスト要件と実際のアプリケーションに焦点を当てているNACE-CIP1-001認証は、業界で非常に尊敬されており、コーティング検査でのキャリアを促進したい人にとって貴重な資産です。
質問 # 46
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. nozzle aperature gauge
- C. surface comparator
- D. replica tape
正解：A
質問 # 47
In a non-convertible coating the role of the primary solvent is to:
- A. To control the evaporation rate
- B. To promote faster cure
- C. To make the coating flow out better
- D. To dissolve the resin
正解：A
質問 # 48
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- C. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- D. perform additional tests secretly to ensure there are no other potential issues at the site
正解：B
質問 # 49
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Achieve consensus through negotiation
- C. Call the supervisor
- D. Never change his/her mind
正解：C
質問 # 50
The least effective method of surface cleaning is most likely
- A. power tool cleaning.
- B. water blasting.
- C. dry grit blasting.
- D. hand tool cleaning.
正解：D
質問 # 51
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Used strictly in immersion service
- C. Applied in very' thin films
- D. Applied in very thick films
正解：C
質問 # 52
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. scratches the surface too deeply resulting in uneven coating application
- B. develops a polished surface, which is a poor anchor profile for most coatings
- C. damages structural elements thereby speeding up the corrosion process.
- D. develops a good anchor profile resulting in uneven coating application.
正解：B
質問 # 53
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 90% of the specified maximum thickness
- C. 70% of the specified maximum thickness
- D. 80% of the specified minimum thickness
正解：D
質問 # 54
Check abrasive blast pressure close to the
- A. compressor
- B. blast nozzle
- C. blast pot
- D. substrate
正解：B
質問 # 55
ASTM Standards are applicable:
- A. In the USA
- B. When specified
- C. In North America
- D. In Asia
正解：B
質問 # 56
Most industrial coatings are:
- A. Organic
- B. Resistant to temperatures above 200C
- C. Resistant to concentrated sulfuric acid
- D. Inorganic
正解：A
質問 # 57
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. Inspectors rarely change on a project.
- C. Management uses them to make personnel decisions.
- D. The information aids communication with supervisors.
正解：A、C、D
質問 # 58
NACE SP 0178 is a standard for:
- A. Stainless steel pipe to be Externally Coated
- B. Tanks and Vessels to be Externally Coated
- C. Tanks and Vessels to, be Lined for Immersion Service
- D. Structural steel to be coated for Atmospheric Service
正解：C
質問 # 59
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Using a damaged gauge
- B. Dragging a gauge through wet coating
- C. Placing the gauge along the longitudinal axis
正解：A、B
質問 # 60
A NACE Coating Inspector is permitted to transport coating material when:
- A. The Inspector should never transport coating material
- B. Asked to do so by the Owner's Representative
- C. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- D. Asked to do so by the Coating Application team
正解：A
質問 # 61
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he can proceed
- B. Advise the Contractor of your readings
- C. Call your supervisor
- D. Advise the Contractor he cannot proceed
正解：B
質問 # 62
Whenever dissimilar metals must join, the most common practice is to
- A. coat all connected dissimilar metals.
- B. provide cathodic protection to prevent corrosion,
- C. provide anodic protection to prevent corrosion.
- D. avoid coating all connected dissimilar metals.
正解：A
質問 # 63
An Inspector should change position when:
- A. The Inspector is convinced by verifiable facts
- B. Only when directed by the supervisor
- C. The Inspectors position is not the majority position
- D. The Owner can save some money by the change
正解：A
質問 # 64
Stripe coats are best applied by:
- A. Airless spray
- B. Brush
- C. Conventional spray
- D. High volume low pressure spray
正解：B
質問 # 65
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. A coating layer applied to the surface to inhibit corrosion
- C. Treating metal with a liquid inhibiter
- D. Complete elimination pf the corrosion process
正解：A
質問 # 66
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 67
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. inhibitor residues
- B. grease and oil
- C. sulfates
- D. soluble chemical salts
正解：B
質問 # 68
......
NACE NACE-CIP1-001テストエンジンPDFで完全版無料問題集：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu