2022年最新のNACE-CIP1-001プレミアム資料テストPDFの無料問題集お試しセット
試験合格を向けてNACE-CIP1-001今すぐ弊社のCIP Level 1試験パッケージを使おう
質問 46
A NACE Coating Inspector is permitted to transport coating material when:
- A. The Inspector should never transport coating material
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. Asked to do so by the Coating Application team
- D. Asked to do so by the Owner's Representative
正解: A
質問 47
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 3
- B. Level 1
- C. Level 2
- D. Level 4
正解: A
質問 48
ISO SA 3 is directly equivalent to:
- A. NACE No. 1/SSPC SP 5
- B. NACE No. 2/SSPC SP 10
- C. None of the above
- D. NACE No. 3/SSPC SP 6
正解: C
質問 49
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record your result by identifying two segments
- B. Use another method as the comparator method is too subjective
- C. Record the segment with the more aggressive profile
- D. Record the segment with the less aggressive profile
正解: D
質問 50
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the product data sheet as a guide
- B. Call the person who wrote the specification for clarification
- C. Call the coating manufacturer for clarification
- D. Use the job specification as a guide
正解: D
質問 51
Which one of these elements is not necessary for corrosion to occur:
- A. Reference Cell
- B. Anode
- C. Cathode
- D. Electrolyte
正解: A
質問 52
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Inorganic
- C. Organic
- D. Resistant to concentrated sulfuric acid
正解: C
質問 53
Osmotic blistering is most likely to occur as a result of
- A. airless spray application
- B. inadequate anchor pattern/surface profile.
- C. overcoating a surface contaminated with chemical salts.
- D. applying tine coating too thin.
正解: A
質問 54
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Very Thorough Blast Cleaning
- D. Light Blast Cleaning
正解: C
質問 55
Stripe coats are best applied by:
- A. Brush
- B. Airless spray
- C. High volume low pressure spray
- D. Conventional spray
正解: A
質問 56
Daily reports are important because:
Select All That Apply
- A. Management uses them to make personnel decisions.
- B. the information impacts future projects.
- C. The information aids communication with supervisors.
- D. Inspectors rarely change on a project.
正解: A,B,C
質問 57
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Using a damaged gauge
- B. Placing the gauge along the longitudinal axis
- C. Dragging a gauge through wet coating
正解: A,C
質問 58
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. In the field only
- B. In the office only
- C. At all times
- D. Only if the specification requires it
正解: C
質問 59
An Inspector should change position when:
- A. The Inspectors position is not the majority position
- B. Only when directed by the supervisor
- C. The Owner can save some money by the change
- D. The Inspector is convinced by verifiable facts
正解: D
質問 60
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. It affects the final appearance after blasting
- C. The Inspector may have to reject the Steel
- D. If the steel is pitted more coating will be required
正解: C
質問 61
SSPC SP 1 identifies the use of:
- A. A wide variety of materials
- B. Biodegradable detergents
- C. Organic solvents
- D. Inorganic solvents
正解: A
質問 62
According to SSPC PA 2 a Spot Measurement is:
- A. A single gauge reading
- B. The average of gauge readings taken in a 4cm (1.5 inch) circle
- C. The overall average of all readings
- D. The average of all spot measurements in a given area
正解: B
質問 63
Which is a component that supplies most of the features and functions of the material?
- A. solvent
- B. additive
- C. pigment
- D. binder
正解: D
質問 64
Upon arrival of coating materials, the inspector should
- A. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- B. observe aryl document that the applicator WFT at regular intervals during application.
- C. observe and document the amount of material and batch numbers.
- D. observe and document time frame and environmental conditions between each coat.
正解: C
質問 65
ISO SA 2 is defined as:
- A. Near White Metal Blasting
- B. Very Thorough Blast Cleaning
- C. Light Blast Cleaning
- D. Thorough Blast Cleaning
正解: D
質問 66
Inspector's daily reports are used:
Select All That Apply
- A. To provide continuity between inspectors
- B. To aid in arbitration between the contractor and client
- C. To help in cases of a coating failure
- D. By the contractor to estimate the amount of work done that day
正解: A,B,C,D
質問 67
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Airless spray equipment
- B. Abrasive blast nozzles
- C. Power tools
- D. Hand tools
正解: C
質問 68
......
2022年最新の問題をマスターCIP Level 1合格目指してNACE-CIP1-001リアル試験!:https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu