[2023年更新]NACE-CIP1-001はCIP Level 1リアルな無料試験練習テスト
無料CIP Level 1 NACE-CIP1-001試験問題を提供します
「コーティングインスペクターレベル1試験」は、表面処理、コーティングアプリケーション、検査技術、安全性と環境配慮、文書化など、幅広いトピックをカバーしています。この試験は、コーティングの欠陥を特定し、適切な修正措置を推奨する個人の能力を評価するよう設計されています。試験は、複数選択問題と実地評価の組み合わせで構成されており、個人の知識を実世界のシナリオに適用する能力をテストします。コーティングインスペクターレベル1試験に合格することは、コーティング業界で品質と安全にコミットすることを証明する重要な成果です。
質問 # 21
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
正解：A
質問 # 22
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 millimeters (.10 inch)
- B. 1 cm (.39 inch)
- C. 2.5 cm (1 inch)
- D. 6.35 cm (2.5 inch)
正解：C
質問 # 23
Which one of the following documents is the best source for coating technical data:
- A. Technical Data Sheet
- B. Application Guidelines
- C. Safety Data Sheet;
- D. Specification
正解：A
質問 # 24
Owners hire NACE Inspectors' with the expectation that:
- A. The inspection cost will be offset by an improvement in service life
- B. The Inspector will make a meaningful technical contribution to the job
- C. a) and c)
- D. The Inspector will improve job flow and schedule
正解：C
質問 # 25
Galvanic corrosion occurs on which of the following substrates:
- A. Fiberglass Reinforced Plastic
- B. Wood
- C. Concrete
- D. Metal
正解：D
質問 # 26
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 105 Gauge Readings resulting in 35 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
正解：D
質問 # 27
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To make the coating flow out better
- C. To control the evaporation rate
- D. To dissolve the resin
正解：C
質問 # 28
The Inspector's Log Book is generally:
- A. Shared with all parties upon project completion
- B. Shredded by the inspector upon project completion
- C. Retained by the inspector upon project completion
- D. Submitted to the client upon project completion
正解：C
質問 # 29
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. NACE 2/SSPC SP10
- C. their best judgment based on similar projects and specifications.
- D. a recognized industry standard like SSPC-PA 2 that is broadly accepted
正解：D
質問 # 30
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- D. Purchase Professional Liability Insurance prior to job commencement
正解：C
質問 # 31
The NACE Inspector should perform tests for soluble salts:
- A. When specified
- B. Prior to coating application
- C. Prior to surface preparation
- D. After surface preparation
正解：A
質問 # 32
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the less aggressive profile
- B. Record the segment with the more aggressive profile
- C. Use another method as the comparator method is too subjective
- D. Record your result by identifying two segments
正解：A
質問 # 33
Removal of welds splatter is required:
- A. On every job
- B. When specifically identified in the owner's specification
- C. When NACE/SSPC abrasive blast standards are specified
- D. When ISO abrasive blast standards are specified
正解：B
質問 # 34
The initial steel condition is important to the NACE Inspector because:
- A. Less abrasive is need if the mill Scale s gone
- B. It affects the final appearance after blasting
- C. If the steel is pitted more coating will be required
- D. The Inspector may have to reject the Steel
正解：D
質問 # 35
NACE SP 0178 is a standard for:
- A. Tanks and Vessels to be Externally Coated
- B. Stainless steel pipe to be Externally Coated
- C. Structural steel to be coated for Atmospheric Service
- D. Tanks and Vessels to, be Lined for Immersion Service
正解：D
質問 # 36
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Ultra-Violet light may contaminant the surface
- B. Presence of weld spatter may produce a false positive
- C. Synthetic oil or grease may not be identified
- D. Chloride salt may produce a false positive
正解：C
質問 # 37
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- B. Break the blisters to see what's inside
- C. Document the problem and advise the Contractor
- D. Document the problem and advise the Contractor and Owner's representative
正解：D
質問 # 38
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Electrolyte
- C. Cathode
- D. Metallic pathway
正解：A
質問 # 39
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A final conflict resolution method
- C. A method to grade surface profile
- D. A general guide
正解：D
質問 # 40
An inspectors personal log book should contain:
- A. Subjective comments re ding the application team
- B. Objective comments regarding the application work
- C. No comments regarding the application team
- D. The inspector's personal opinions of the application team
正解：C
質問 # 41
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. Only if the specification requires it
- B. At all times
- C. In the office only
- D. In the field only
正解：B
質問 # 42
......
NACE-CIP1-001（コーティングインスペクターレベル1）認定試験は、耐久性、密着力、総合品質に対する塗料の検査に関与する個人の知識とスキルを評価するために設計されています。この認定は、世界的に認知されており、National Association of Corrosion Engineers（NACE）Internationalによって提供されています。これは、個人がコーティング検査の分野での熟練度を証明し、就職市場で競争力を持つことができる基本的な認定です。
NACE NACE-CIP1-001リアルな問題と知能問題集：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu