[2024年01月13日] 完全版最新の問題集でPDFで最新NACE-CIP1-001試験問題と解答
無料で使えるNACE-CIP1-001試験問題集で100%合格できる試験簡単に合格させるJPNTest
NACE-CIP1-001認定資格は、塗装業界で高く評価されており、塗装検査の高度な知識と専門技術を証明します。この認定資格は、世界的に認知されており、多くの雇用者にとって必須の要件です。認定資格は、個人がキャリアを発展させ、収入を増やす機会を提供します。さらに、認定資格は塗料が正しく施工されることを保証し、構造物や設備の寿命と信頼性に貢献します。
NACE-CIP1-001認定を取得することは、腐食防止分野における候補者のコミットメントと高品質なコーティング検査を実施する能力を示すことになります。これにより、求職機会の増加、高い収入、業界内でのより大きな尊敬を得ることができます。
コーティング検査員は、建設業界における重要な役割を担っています。これらの専門家は、業界基準や手順に従ってコーティングとライニングのプロセスを検査し、評価し、確認する責任があります。腐食防止技術者協会（NACE）は、コーティング検査員のスキルと知識を検証する認定プログラムを提供しています。NACE-CIP1-001試験は、コーティング検査員レベル1用に予約された認定プログラムです。
質問 # 37
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Call the supervisor
- B. Never change his/her mind
- C. Achieve consensus through negotiation
- D. Go with the majority opinion
正解：A
質問 # 38
Inspection documentation is important because:
- A. Owners use the documentation for a variety of purposes
- B. a) only
- C. a) & b)
- D. It is the only deliverable item provided by the inspector
正解：A
質問 # 39
ISO SA 2 is defined as:
- A. Near White Metal Blasting
- B. Light Blast Cleaning
- C. Thorough Blast Cleaning
- D. Very Thorough Blast Cleaning
正解：C
質問 # 40
Which one of the following documents is the best source for coating technical data:
- A. Safety Data Sheet;
- B. Specification
- C. Application Guidelines
- D. Technical Data Sheet
正解：D
質問 # 41
Stripe coats are generally applied to:
- A. Complex geometric shapes
- B. Welds
- C. a), b), and c)
- D. Edges and corners
正解：C
質問 # 42
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 90% of the specified maximum thickness
- C. 80% of the specified minimum thickness
- D. 70% of the specified maximum thickness
正解：C
質問 # 43
Removal of welds splatter is required:
- A. When ISO abrasive blast standards are specified
- B. When NACE/SSPC abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. On every job
正解：C
質問 # 44
The NACE Inspector should perform tests for soluble salts:
- A. Prior to surface preparation
- B. Prior to coating application
- C. After surface preparation
- D. When specified
正解：D
質問 # 45
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Submitted before the end of the job
- C. Timely, accurate and concise
- D. Always handwritten
正解：C
質問 # 46
Conventional spray is a good choice when:
- A. High viscosity coatings are being applied
- B. High production rates are required
- C. High transfer efficiency is required
- D. High quality finishes are required
正解：D
質問 # 47
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Meet with the prospective employer to determine the scope of your role
- C. Accept the assignment without hesitation
- D. Advise the prospective employer that you cannot accept the position
正解：B
質問 # 48
Check abrasive blast pressure with a
- A. surface comparator
- B. nozzle aperature gauge
- C. replica tape
- D. needle pressure gauge
正解：D
質問 # 49
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Applied in very thick films
- C. Applied in very' thin films
- D. Used strictly in immersion service
正解：C
質問 # 50
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades 1-4
- B. Rust Grades A-D
- C. Surface Condition H
- D. Surface Conditions E-G
正解：B
質問 # 51
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Document the problem and advise the Contractor
- C. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- D. Document the problem and advise the Contractor and Owner's representative
正解：D
質問 # 52
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Call your supervisor
- B. Advise the Contractor of your readings
- C. Advise the Contractor he can proceed
- D. Advise the Contractor he cannot proceed
正解：B
質問 # 53
Solvents are added to coating formulations to
- A. decrease film permeability.
- B. dissolve binders and form liquid coatings.
- C. provide color.
- D. increase film permeability.
正解：B
質問 # 54
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
- B. Advise the owners' representative of your lack of knowledge in this area
- C. Carefully review the document and do the best you can
- D. Hire a third patty to assist you in understanding the document
正解：C
質問 # 55
NACE SP 0178 is a standard for:
- A. Stainless steel pipe to be Externally Coated
- B. Tanks and Vessels to, be Lined for Immersion Service
- C. Tanks and Vessels to be Externally Coated
- D. Structural steel to be coated for Atmospheric Service
正解：B
質問 # 56
Polymerization is the process of:
- A. All organic coatings
- B. Monomers joining together
- C. Monomers telegraphing
- D. All thermoplastic coatings
正解：B
質問 # 57
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Owner's Representative
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. The Inspector should never transport coating material
- D. Asked to do so by the Coating Application team
正解：C
質問 # 58
ISO SA 3 is directly equivalent to:
- A. NACE No. 1/SSPC SP 5
- B. None of the above
- C. NACE No. 3/SSPC SP 6
- D. NACE No. 2/SSPC SP 10
正解：B
質問 # 59
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. the highest temperature at which moisture forms on a steel surface.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. a measure of the amount of moisture in the air compared to saturation level.
正解：D
質問 # 60
......
無料で試せるNACE-CIP1-001試験問題NACE-CIP1-001実際の無料試験問題：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu