NACE-CIP1-001試験をパスするなら弊社のCIP Level 1試験パッケージを今すぐゲットして合格せよ
完全版最新の2023年最新のNACE-CIP1-001試験問題集テストガイド、専門トレーニングJPNTest
質問 17
Silicone coatings are typically:
- A. Applied in very' thin films
- B. Used as a sacrificial primer
- C. Applied in very thick films
- D. Used strictly in immersion service
正解: A
質問 18
The Inspector's Log Book is generally:
- A. Submitted to the client upon project completion
- B. Retained by the inspector upon project completion
- C. Shredded by the inspector upon project completion
- D. Shared with all parties upon project completion
正解: B
質問 19
Owners hire NACE Inspectors' with the expectation that:
- A. The inspection cost will be offset by an improvement in service life
- B. The Inspector will make a meaningful technical contribution to the job
- C. The Inspector will improve job flow and schedule
- D. a) and c)
正解: D
質問 20
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:
- A. Low Surface Temperature
- B. High Surface Temperature
- C. High Relative Humidity
- D. Low Relative Humidity
正解: D
質問 21
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. checking.
- B. alligatoring.
- C. blistering.
- D. cracking.
正解: A
質問 22
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. replica tape
- C. surface comparator
- D. nozzle aperature gauge
正解: A
質問 23
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
正解: C
質問 24
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Assume the role of the Safety Inspector
- B. Check the credentials of the Safety Officer on site
- C. Act in accordance with the site safety requirements and set an example
- D. Check the PPE used by the Applicators
正解: C
質問 25
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. General Corrosion
- C. Galvanic Corrosion
- D. Localized Corrosion
正解: C
質問 26
What is used to determine compressed air cleanliness?
- A. Needle pressure gauge
- B. Blotter test
- C. Profilometer
- D. Psychrometer
正解: C
質問 27
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Use the job specification as a guide
- B. Use the product data sheet as a guide
- C. Call the coating manufacturer for clarification
- D. Call the person who wrote the specification for clarification
正解: A
質問 28
An inspectors personal log book should contain:
- A. Subjective comments re ding the application team
- B. The inspector's personal opinions of the application team
- C. No comments regarding the application team
- D. Objective comments regarding the application work
正解: C
質問 29
Dew point is the temperature at which
- A. condensation occurs.
- B. water freezes.
- C. humidity decreases
- D. the air is saturated.
正解: A
質問 30
Check abrasive blast pressure close to the
- A. blast nozzle
- B. blast pot
- C. compressor
- D. substrate
正解: A
質問 31
Removal of surface contaminants is done by:
- A. Waterjetting
- B. Scarifying
- C. A combination of methods
- D. Abrasive blasting
正解: C
質問 32
Most industrial coatings are:
- A. Organic
- B. Resistant to temperatures above 200C
- C. Inorganic
- D. Resistant to concentrated sulfuric acid
正解: A
質問 33
ASTM Standards are applicable:
- A. When specified
- B. In Asia
- C. In North America
- D. In the USA
正解: A
質問 34
Which one of these elements is not necessary for corrosion to occur:
- A. Electrolyte
- B. Reference Cell
- C. Cathode
- D. Anode
正解: B
質問 35
......
2023年最新の問題CIP Level 1合格目指してNACE-CIP1-001リアル試験をマスターせよ!:https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu