NACE-CIP1-001練習問題集で検証済みで更新された100問題あります
更新されたNACE-CIP1-001試験問題集でPDF問題とテストエンジン
質問 # 27
Which one of the following documents is the best source for coating technical data:
- A. Technical Data Sheet
- B. Specification
- C. Safety Data Sheet;
- D. Application Guidelines
正解：A
質問 # 28
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. grease and oil
- B. inhibitor residues
- C. sulfates
- D. soluble chemical salts
正解：A
質問 # 29
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A general guide
- C. A final conflict resolution method
- D. A method to grade surface profile
正解：B
質問 # 30
Stripe coats are best applied by:
- A. Conventional spray
- B. Airless spray
- C. High volume low pressure spray
- D. Brush
正解：D
質問 # 31
Digital hygrometers
- A. use a thermocouple in contact with the surface to measure temperature
- B. determine relative humidity, air temperature, and dew point temperature:
- C. are used to measure temperature from a distance.
- D. consist of a bimetallic sensing element protected from wind gusts.
正解：B
質問 # 32
To be of value the Inspector's documentation must be:
- A. Always typewritten
- B. Timely, accurate and concise
- C. Submitted before the end of the job
- D. Always handwritten
正解：B
質問 # 33
Surface profile describes:
- A. The level of surface roughness required after abrasive blasting
- B. The general condition of the surface required after abrasive blasting
- C. The initial condition of the surface prior to abrasive blasting
- D. The level of surface cleanliness required after abrasive blasting
正解：A
質問 # 34
To achieve consistently accurate results with ALL alt test equipment
- A. wash your hands before sampling.
- B. calibrate the instrument in the field.
- C. avoid placing the sample discs on a surface.
- D. wear gloves when sampling.
正解：A
質問 # 35
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- B. NACE 2/SSPC SP10
- C. their best judgment based on similar projects and specifications.
- D. a detailed checklist and document the lack of a standard.
正解：A
質問 # 36
Inspector's daily reports are used:
Select All That Apply
- A. To aid in arbitration between the contractor and client
- B. By the contractor to estimate the amount of work done that day
- C. To help in cases of a coating failure
- D. To provide continuity between inspectors
正解：A、B、C、D
質問 # 37
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. surface comparator
- C. replica tape
- D. nozzle aperature gauge
正解：A
質問 # 38
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 75 Gauge Readings resulting in 25 Spot Measurements
- B. 45 Gauge readings resulting in 15 Spot Measurements
- C. 105 Gauge Readings resulting in 35 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
正解：D
質問 # 39
A successful coating inspector must be able to
- A. recommend the appropriate coating technique for the job to the contractor.
- B. apply the coating with expert accuracy.
- C. advise the coating applicator on how to mix the coating.
- D. look for problems or issues during application.
正解：D
質問 # 40
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. Yes, because the 'two standards are not equivalent
- C. It depends on which hand tool the Contractor selects
- D. No, because there is no real difference in the standards
正解：D
質問 # 41
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To make the coating flow out better
- C. To control the evaporation rate
- D. To dissolve the resin
正解：C
質問 # 42
Which of these tests uses a syringe?
- A. Potassium ferricyanide
- B. Bresle patch
- C. Soluble salts meter
- D. Sleeve test
正解：B
質問 # 43
Osmotic blistering is most likely to occur as a result of
- A. overcoating a surface contaminated with chemical salts.
- B. airless spray application
- C. inadequate anchor pattern/surface profile.
- D. applying tine coating too thin.
正解：B
質問 # 44
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Resistant to concentrated sulfuric acid
- C. Inorganic
- D. Organic
正解：D
質問 # 45
Owners hire NACE Inspectors' with the expectation that:
- A. a) and c)
- B. The inspection cost will be offset by an improvement in service life
- C. The Inspector will make a meaningful technical contribution to the job
- D. The Inspector will improve job flow and schedule
正解：A
質問 # 46
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 1 cm (.39 inch)
- B. 2.5 cm (1 inch)
- C. 6.35 cm (2.5 inch)
- D. 2.5 millimeters (.10 inch)
正解：B
質問 # 47
......
最新（2024)NACE NACE-CIP1-001試験問題集：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu
最適な練習法にはNACE NACE-CIP1-001試験の素晴らしいNACE-CIP1-001試験問題PDF：https://drive.google.com/open?id=1iNBXtMZ-zkgFVd82IqXLyIpf_lNVSMdV