[2026年02月] 更新されたのはNACE NACE-CIP1-001問題集PDFオンラインエンジン
NACE-CIP1-001.PDFで問題解答！サンプル問題は信頼され続けます
質問 # 40
Prior to using Inspection Tools the inspector must:
- A. a), b) & c)
- B. Ensure the instrument is within calibration parameters
- C. Read the manufactures' instructions
- D. Be trained on how to use the instrument
正解：A
質問 # 41
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Applied in very thick films
- C. Applied in very' thin films
- D. Used strictly in immersion service
正解：C
質問 # 42
A magnetic pull-off type gauge is a good choice when:
- A. When working on non-ferrous metals
- B. Performing an adhesion test
- C. Accuracy is not required
- D. When an intrinsically safe tool is required
正解：D
質問 # 43
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Using a damaged gauge
- B. Dragging a gauge through wet coating
- C. Placing the gauge along the longitudinal axis
正解：A、B
質問 # 44
The least effective method of surface cleaning is most likely
- A. dry grit blasting.
- B. hand tool cleaning.
- C. power tool cleaning.
- D. water blasting.
正解：B
質問 # 45
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- B. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
- D. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
正解：C
質問 # 46
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Conditions E-G
- B. Rust Grades 1-4
- C. Rust Grades A-D
- D. Surface Condition H
正解：C
質問 # 47
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Power tools
- B. Abrasive blast nozzles
- C. Airless spray equipment
- D. Hand tools
正解：A
質問 # 48
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 49
According to SSPC PA 2 a Spot Measurement is:
- A. The overall average of all readings
- B. The average of all spot measurements in a given area
- C. A single gauge reading
- D. The average of gauge readings taken in a 4cm (1.5 inch) circle
正解：D
質問 # 50
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 2
- B. Level 1
- C. Level 4
- D. Level 3
正解：D
質問 # 51
Digital hygrometers
- A. are used to measure temperature from a distance.
- B. use a thermocouple in contact with the surface to measure temperature
- C. consist of a bimetallic sensing element protected from wind gusts.
- D. determine relative humidity, air temperature, and dew point temperature:
正解：D
質問 # 52
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Call your supervisor
- B. Advise the Contractor of your readings
- C. Advise the Contractor he cannot proceed
- D. Advise the Contractor he can proceed
正解：B
質問 # 53
Surface profile describes:
- A. The initial condition of the surface prior to abrasive blasting
- B. The level of surface roughness required after abrasive blasting
- C. The level of surface cleanliness required after abrasive blasting
- D. The general condition of the surface required after abrasive blasting
正解：B
質問 # 54
Removal of welds splatter is required:
- A. On every job
- B. When ISO abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. When NACE/SSPC abrasive blast standards are specified
正解：C
質問 # 55
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
正解：A
質問 # 56
......
NACE NACE-CIP1-001問題集PDFのベストを目指すなら問題集を使おう！高得点目指すならここ：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu
CIP Level 1 NACE-CIP1-001試験と認定テストエンジン：https://drive.google.com/open?id=1VTX4Q3Ainaobn7pQmItRTHjLQPtJIcJE