[2026年04月] 合格させるNACE NACE-CIP1-001テストエンジンPDFで完全版無料問題集
Coating Inspector Level 1練習テスト2026年最新のNACE-CIP1-001ストレスなしで合格！
NACE-CIP1-001認定試験を受ける資格を得るには、候補者はコーティング検査の分野で最低2年の経験が必要です。試験は100の複数選択の質問で構成されており、4時間以内に完了する必要があります。この試験の合格スコアは70％です。認定されると、個人は、石油およびガス産業、航空宇宙、建設、製造の役割など、幅広いキャリアの機会を利用できると予想できます。
NACE-CIP1-001認定は、コーティング業界の個人と企業の両方にとって重要です。個人にとって、認定はこの分野での専門知識とプロフェッショナリズムを実証し、雇用機会の増加と給与の増加につながる可能性があります。企業の場合、NACE認定のコーティング検査官を雇用することで、プロジェクトが最高水準に完了することを保証します。これにより、より多くのビジネスを獲得し、費用のかかる間違いを避けることができます。
質問 # 35
Stripe coats are best applied by:
- A. Conventional spray
- B. Airless spray
- C. Brush
- D. High volume low pressure spray
正解：C
質問 # 36
Silicone coatings are typically:
- A. Used strictly in immersion service
- B. Applied in very' thin films
- C. Applied in very thick films
- D. Used as a sacrificial primer
正解：B
質問 # 37
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. Yes, because the 'two standards are not equivalent
- B. No, because there is no real difference in the standards
- C. It depends on which power tool the Contractor selects
- D. It depends on which hand tool the Contractor selects
正解：B
質問 # 38
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
正解：D
質問 # 39
Owners hire NACE Inspectors' with the expectation that:
- A. a) and c)
- B. The inspection cost will be offset by an improvement in service life
- C. The Inspector will improve job flow and schedule
- D. The Inspector will make a meaningful technical contribution to the job
正解：A
質問 # 40
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Localized Corrosion
- B. Galvanic Corrosion
- C. General Corrosion
- D. Atmospheric Corrosion
正解：B
質問 # 41
ISO SA 2.5 is defined as:
- A. Light Blast Cleaning
- B. Very Thorough Blast Cleaning
- C. Thorough Blast Cleaning
- D. Near White Metal Blasting
正解：B
質問 # 42
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 1/SSPC SP 5
- C. NACE No. 2/SSPC SP 10
- D. NACE No. 3/SSPC SP 6
正解：A
質問 # 43
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
正解：B
質問 # 44
An Inspector should change position when:
- A. Only when directed by the supervisor
- B. The Owner can save some money by the change
- C. The Inspectors position is not the majority position
- D. The Inspector is convinced by verifiable facts
正解：D
質問 # 45
In a non-convertible coating the role of the primary solvent is to:
- A. To promote faster cure
- B. To make the coating flow out better
- C. To control the evaporation rate
- D. To dissolve the resin
正解：C
質問 # 46
An inspectors personal log book should contain:
- A. The inspector's personal opinions of the application team
- B. Objective comments regarding the application work
- C. No comments regarding the application team
- D. Subjective comments re ding the application team
正解：C
質問 # 47
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
正解：C
質問 # 48
Relative humidity is
- A. a measure of the amount of moisture in the air compared to saturation level.
- B. the lowest temperature at which moisture forms on a steel surface.
- C. the highest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to the air temperature.
正解：A
質問 # 49
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Conditions E-G
- B. Rust Grades A-D
- C. Rust Grades 1-4
- D. Surface Condition H
正解：B
質問 # 50
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Use another method as the comparator method is too subjective
- B. Record your result by identifying two segments
- C. Record the segment with the more aggressive profile
- D. Record the segment with the less aggressive profile
正解：D
質問 # 51
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. blotter test for the presence of oil and water.
- B. dry film thickness (DEI) measurement.
- C. wet film thickness (WFT) measurement.
- D. vial lest.
正解：A
質問 # 52
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Cathode
- C. Metallic pathway
- D. Electrolyte
正解：A
質問 # 53
Safety Data Sheets must be carefully reviewed by:
- A. All personnel involved in the job
- B. The Owner's personnel
- C. The Inspection personnel
- D. The Application personnel
正解：A
質問 # 54
......
NACE-CIP1-001試験に合格した個人は、基本的なコーティング検査タスクを実行する資格があると見なされます。コーティングの欠陥を特定し、基本的な表面準備を実行し、さまざまな環境でコーティングの適切な使用を認識できます。この認証は、石油とガス、海洋、インフラなどの産業で非常に評価されています。また、コーティングインスペクターとしてのキャリアを追求したい、または一般的なコーティング業界でのキャリアを追求したい個人にとっても優れた出発点です。
時間限定！今すぐ無料アクセスNACE-CIP1-001練習試験用問題：https://drive.google.com/open?id=1iNBXtMZ-zkgFVd82IqXLyIpf_lNVSMdV
オンライン試験練習テストと詳細な解説付き！：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu