[2024年07月31日] 心強いNACE-CIP1-001のPDF問題集はNACE-CIP1-001問題
正真正銘のNACE-CIP1-001問題集で無料PDF問題で合格させる
質問 # 39
To be of value the Inspector's documentation must be:
- A. Submitted before the end of the job
- B. Always typewritten
- C. Timely, accurate and concise
- D. Always handwritten
正解：C
質問 # 40
Which is a component that supplies most of the features and functions of the material?
- A. binder
- B. pigment
- C. solvent
- D. additive
正解：A
質問 # 41
Upon arrival of coating materials, the inspector should
- A. observe and document the amount of material and batch numbers.
- B. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
- C. observe aryl document that the applicator WFT at regular intervals during application.
- D. observe and document time frame and environmental conditions between each coat.
正解：A
質問 # 42
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
正解：D
質問 # 43
The most important factor resulting in improved job site safety is:
- A. Personal Protective Equipment
- B. Situational Awareness
- C. Safety Enforcement
- D. Engineering Controls
正解：B
質問 # 44
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Resistant to concentrated sulfuric acid
- C. Organic
- D. Inorganic
正解：C
質問 # 45
ASTM Standards are applicable:
- A. When specified
- B. In the USA
- C. In North America
- D. In Asia
正解：A
質問 # 46
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. True
- B. False
正解：A
質問 # 47
Removal of welds splatter is required:
- A. On every job
- B. When ISO abrasive blast standards are specified
- C. When NACE/SSPC abrasive blast standards are specified
- D. When specifically identified in the owner's specification
正解：D
質問 # 48
Which one of the following documents is the best source for coating technical data:
- A. Specification
- B. Safety Data Sheet;
- C. Technical Data Sheet
- D. Application Guidelines
正解：C
質問 # 49
What is used to determine compressed air cleanliness?
- A. Blotter test
- B. Psychrometer
- C. Profilometer
- D. Needle pressure gauge
正解：C
質問 # 50
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 1/SSPC SP 5
- C. NACE No. 3/SSPC SP 6
- D. NACE No. 2/SSPC SP 10
正解：A
質問 # 51
Corrosion generally occurs at which of the following sites:
- A. Anode
- B. Cathode
- C. Metallic pathway
- D. Electrolyte
正解：A
質問 # 52
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. A method to grade surface profile
- B. Pass/fail criteria
- C. A general guide
- D. A final conflict resolution method
正解：C
質問 # 53
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to saturation level.
- C. a measure of the amount of moisture in the air compared to the air temperature.
- D. the highest temperature at which moisture forms on a steel surface.
正解：B
質問 # 54
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. their best judgment based on similar projects and specifications.
- C. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- D. NACE 2/SSPC SP10
正解：C
質問 # 55
Whenever dissimilar metals must join, the most common practice is to
- A. provide cathodic protection to prevent corrosion,
- B. provide anodic protection to prevent corrosion.
- C. coat all connected dissimilar metals.
- D. avoid coating all connected dissimilar metals.
正解：C
質問 # 56
The Inspector should record the serial numbers of inspection instruments:
- A. Each time the instrument is used
- B. Only if the specification requires it
- C. Only when verifying accuracy of the instrument
- D. Only if the instrument is suspected of not working properly
正解：A
質問 # 57
Which of these tests uses a syringe?
- A. Bresle patch
- B. Soluble salts meter
- C. Sleeve test
- D. Potassium ferricyanide
正解：A
質問 # 58
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:
- A. transitioning.
- B. juxtaposing.
- C. telegraphing.
- D. monitoring
正解：C
質問 # 59
......
結果を保証するには最新2024年07月無料：https://www.jpntest.com/shiken/NACE-CIP1-001-mondaishu
有効な問題最新版を無料で試そうNACE-CIP1-001試験問題集解答：https://drive.google.com/open?id=1P1lfDzEaKqgLnlveMfiYqRxWMsP9t_R2